ender 3 z axis support 3d models

... than outher plastics. You also will need 4 more M5 bolts same size as the outhers. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Infill: 50% or more Filament: HatchBox Pla or Abs Category: 3D Printer Accessories

I upgraded the printer's drive system with a new z-axis drive for enhanced stability. The lead screw for this axis is notably long, as evident from the attached photo. Initially, I had planned to shorten it, but then I opted to add a die on top...

Cable Bracket for use with the Teaching Tech rear controller box. https://www.thingiverse.com/thing:3688967 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15% Filament: NA ABS...

A compact z axis floating bearing without magnets. Uses 8 balls 2.2-2.4mm dia. balls (from a 16x8x6mm bearing) 1. Print all four parts on the flat sides. 2. Use sand paper to smooth the top printed surfaces which mate with each other. 3. Use...

I've also moved to a top-mounted, double lead screw, design (https://www.thingiverse.com/thing:4569498) so do not have a need for this z-axis motor mount any longer. This is a remix of a remix created by Alloca. Original motor mount design by...

... the extra spacing material that Alloca added to their specific setup, and repositioned the mounting holes to match the original design by Hangtight. It should work just fine on a stock setup, assuming your z-axis nut mount isn't way off center.

Z-axis limit switch regulator. It has discrete adjustment with a step of 0.025 mm. Printed from PLA with 100% coverage. The dovetail, after a short grinding and lubrication with grease for plastic, moves without play and effort. Bolt or hairpin Ф4...

My 2nd z-axis has a different size hole, I modified the design a bit Filament i...

it is in fact 12.12mm where it mounts to the upright, but 11.9 where to countersink heads are, meaning the flat surface where the motor mounts to is in fact at an 90.6 deg angle to the uprights, which is why the z axis bar is tight as it get down...

Cheapest dual z upgrade, i prefer to buy the device myself and use the printer to upgrade itself, cheaper and DIY My 2nd z-axis has a different size hole, I modified the design a bit Filament i use:...

I'm using BMG clone extruder and the cable guide from llueen can't be fit directly - Z-axis brass nut blocking part of the guide. I have to remove some parts to get it fit. * llueen cable guide: https://www.thingiverse.com/thing:4723800 Also,...

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When I print this, the orientation on the printing bed is best with the chain side facing up and the cable hole on top. The first versions weren't strong enough with 20%...

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When printing this, the orientation on the printing bed is best with the chain side up and the cable hole at the top. The first versions were not strong enough with 20%...

The "Ender 3 Lead Screw Stabilizer" project was published on September 2, 2018, and can be found at www.thingiverse.com/thing:3080912. After making some adjustments to the original design, I no longer need to secure it with screws. ...Instead, I simply...

I was fixing my OG ender 3 and cracked the plastic mount that came with my printer, hope this will help others with the same issue. ...May need to use super glue on the threads of the circuit board screws if they do not catch into the plastic, 20%...

This is a knob (kit) to help spin that corkscrew for the Z-axis stepper motor to lift and lower the extruder assembly. I've had it with trying to spin on on the stepper or corkscrew. The lever.stl is for those that doesn't mind having it...

I recently upgraded the printer with a double Z-axis consisting of a lead screw and a stepper motor, and later I also added a timing belt so that when the stepper motors are disabled they do not go out of sync, but the first time I put a 610 belt on...

I finally made my own part after testing several models without any success, but this one works perfectly on my Ender 3 Pro. For the base, you will need longer screws to attach it securely to the printer, while the original screws for the motor mount...

I'm adding a second Z stepper motor/screw thanks to the Dual Z Axis Ender 3 / 3Pro by CR83D Since I'll be using direct drive extruder I no longer need the original part with extruder mount. In my case it was bent uneven, so the 3d printed part...

A small modification to use another kind of screws. Screws M3 6mm : https://fr.aliexpress.com/item/32825015459.html Nuts 20S-M3 : https://fr.aliexpress.com/item/32825357262.html Print Settings Printer Brand: Creality Printer: Ender 3 Category: 3D...

This is a part for ender 3 that extends the bar at a angle that way you dont lose space when you get a direct drive extruder like the microswiss direct drive kit. Is also useful if you just need to maximise your print volume. It can be angled twards...

Os dejo mi diseño para la estabilizacion del eje Z , se puede modificar con el programa cortador segun tus caracteristicas

Z-Bracket Spacer for Ender3 Z-Motor helps with making straight big bolt :D Its just 0.5 milimeter but made my big z-bolt perfectly straight and parrel to the frame. Happy priniting and u can print in in highest possible quality its just 5 mins of...

The components required for this project are as follows: - nema 17: a motor size specification, specifically a 34 or 40mm diameter - lead screw: an T8, P2, L8 screw with a nut attached - coupler: a 5 x 8mm device used to connect the motor and lead...

Remix: - https://www.thingiverse.com/thing:4699747 Purpose: - Adjustable mount for Z-Stepper Required: - M4 bolts (4020 rail mounting) - M4 t-nuts - M3 bolts (stepper mounting)

Remix: - https://www.thingiverse.com/thing:4699747 Purpose: - Adjustable mount for Z-Stepper Required: - M4 bolts (4020 rail mounting) - M4 t-nuts - M3 bolts (stepper mounting)

My print settings are as follows: - Sliced with Ultimaker Cura 3.6 - Speed: 60 mm/s (first layer: 30 mm/s) - Temperature: 242/75 °C (PET-G) - Top/bottom patterns: lines - Support pattern: zig zag - Raft: yes, 0.8 mm thick - Infill: 100% You will...

I designed this cover/guard to help protect the exposed switch body and the printed circuit board that the z-limit switch is mounted to. ...There is some play in the cutout for vertical adjustment of the switch.

you will need to edit the following in marlin: #define DISABLE_INACTIVE_Z false (This will be marked as "true", change it to "false") //#define SD_FINISHED_STEPPERRELEASE (this will be uncommented, you need to comment this out and turn it off)...

I created the design to follow 0.12mm increments to follow the default Cura settings for Ender 3s. I printed these at 0.12mm to get the best resolution on the spacer thickness. ... You can see these kinds of brackets being used in this video: ...