ender 3 y splitter 3d models

Created this remix to fit the stock belt on the Ender 3 V2, it works but only uses two screws (as the stock mount does).

This is a Cable Guide for the Creality Ender 3 Printbed. ...It is supposed to look alike to the design of the origininal cable holder.

Created this remix to fit the stock belt on the Ender 3 V2, it works but only uses two screws (as the stock mount does).

I really liked this design, especially the belt tensioners. ...However the plate did not fit on my standard ender 3, so I redesigned the plate

Tinkered a custom Y-rail mount to fit seamlessly onto my Ender 3's standard rail system. Next, I successfully modified the 2020 ball-joint knob to integrate perfectly with the new setup. I paired this innovative modification with eatthistim's...

... is dead cold to the touch, it appears it doesn't even need cooling veins to efficiently cool the motor. Might revisit in the future and lower the shroud to speed up airflow along the top though as is it is a great cooling addition to the Ender 3 v2

You'll require two RA brackets and three small bracing plates to install a single 2020 V-slot linear rail support on an Ender-3 or any printer that utilizes V-slot extrusions.

This is a minor stylistic change to Jody_T's rail cover to match the rest of the [Better Ender 3] series of parts I've created or modified.

The Ender 3 Pro rail cover mod is a modification based on Skorm3d's original design. ...This version of the mod eliminates the need for a separate fitting, making it easier to install and set up.

**UPDATE** *I've adjusted the size to make for better tolerances, V1.1 .STL and .STEP is uploaded.* **DESCRIPTION** I completely reverse engineered and recreated da_syggy's Ender 3 Pro Rail Cover as it's not completely flat and straight. Otherwise I...

Bracket for the Creality Ender 3 which offsets the y-axis limit switch forward to account for reduced travel due to stepper motor dampers. This bracket uses standard hardware to attach to the y-axis aluminum. I opted to use two holes instead of a...

Y Tensioner for Ender 3 Mk7 Version Upgraded the guide system and simplified all the models Unified the screws dimensions with my other tensioner versions Modified the minimum belt tensioning position for short belts Increased the tolerances compared...

Y Tensioner for Ender 3 Mk7 Version Upgraded guide system and simplified all models Unified screw dimensions across versions Modified minimum belt tensioning position for short belts Increased tolerances compared to previous models Added a New...

This mount is intended to be used on an Ender 3 Pro Y-Axis. The mount has a 9mm offset so it can be used with larger motors, or stepper motor dampers. My machine is equipped with a 48mm stepper motor which necessitated this mount. This stepper...

Updated Design:2019-03-12 - I released a totally new design that is much simpler and cleaner.Check it out over ➠ hereOriginal Design:When I originally ordered my Ender 3, I also purchased a few stepper motor dampeners. To my dismay, the stepper...

This is a four way splitter for connecting tubes to for venting smoke/vape.

This is a four way splitter for connecting tubes to for venting smoke/vape.

It is possible to attach heatsink to the motor if worried, or if you have attached the All In One case on the back side of your Ender 3 Pro, you can direct the air up towards the motor instead of down towards the floor. The mount is assembled in the...

... any fiddling with the end stop. Also, be sure to check out these other modifications that significantly reduce the sound of your Ender 3: * X-Axis Stepper Damper * Z-Axis Stepper Damper * Low Profile Feet Enjoy a quieter printing experience!

There is complete clearance of an Ender 3 v1's print bed at full extension and no risk of hitting the print that I can tell. The articulations go together with M3x20's and a nut. I suggest a washer as well, so minor angle adjustments don't knock...

E3D j-head Y-Splitter (2-3-4-way) direct and bowden to bowden Watch the video of it doing the swaps here, https://youtu.be/g-apfMQabjg. I made this video to help someone, and maybe it can help others too. The code that is running in the video is...

Someone made a better version, get it here: https://www.thingiverse.com/thing:4968880 ------------------------------------- I couldn't find a cover for the backside of the Y-Axis of my Ender. There's a spinny wheel with a teethy belt around it, way...

You should probably use a drill press for this since it requires more accuracy.On my quest to print at very high speeds on my Ender 3 Pro, I noticed some room for improvement in the Y axis mechanics.The V rollers were inconsistent and unreliable, the...

My conversion Ender 3 to linear rods. Before conversion I had 30-32 Hz on Y axis, now it's 43.25 Hz. Printer works best in range 2000-2500mm/s2 acceleration. Normal speeds are up to 150mm/s for technical parts and 50-80mm/s for organic, like faces...

I also replaced the nut from Olev's design with idig3d's knob, which is a better fit for my Creality Ende-3 3D printer. As part of upgrading my Creality Ende-3, I've made some changes to the tensioner. ...I updated the side plates because they were...

The original file utilized different screws than the ones originally used in the ender 3. They didn't fit so I changed the diameter of these holes. This version is intended to be used with button head m5 bolts with the head having a diameter of...

This is a remix from https://www.thingiverse.com/thing:5158277 , the original design used socket head bolts instead of standard cap head screws which are found in ender 3 models. This remix increases the tolerances of the holes for both the M3 and M5...

This is a remix from https://www.thingiverse.com/thing:5158277 , the original design used socket head bolts instead of standard cap head screws which are found in ender 3 models. This remix increases the tolerances of the holes for both the M3 and M5...

... other parts from the original post. I took the original design and chopped off 7mm from the end to allow my ender 3 pro's bed to utilize the full 235mm on the axis. ...The original design caused the bed to hit the tensioner when fully extended.

**It only fits the Ender 3 Pro with a 4040 center extrusion.** This bracket is needed because some Ender 3 Printers are shipped with pressed pulleys on the stepper motors. Those pressed on pulleys can't be adjusted along the shaft of the motor. All...