ender 3 y motor mount 3d models

This angled/wedged spacer set allows you to correctly align the Y stepper motor to the Y axis on your Ender 3 Pro. It fits between the Y motor bracket and the 40x40 mm Y axis aluminium profile. The wide cut-outs make sure that it does not touch the...

This angled/wedged spacer set allows you to correctly align the Y stepper motor to the Y axis on your Ender 3 Pro. It fits between the Y motor bracket and the 40x40 mm Y axis aluminium profile. The wide cut-outs make sure that it does not touch the...

I made these dampers to try and reduce the noise of the motors on the newer versions of the ender 3 pros (2020). I originally bought dampers however it is a pain to install on these newer models. I designed a small damper to go in between the motor...

So I wanted to put on a larger motor and a dampener for the y and x-axis on my Ender 3. Turns out the motor was far too big and when I went to make a whole new bracket I had an idea: just flip the Y-axis bracket vertically and mount that way. The new...

Y Axis Motor Mount Body for Ender S1/ S1 Pro to match the belt tensioner body I replaced. The Y Axis limit sensor slides in and is friction fit.  The model requires the attached pull tab to clip on to the wiring connector.  This allows...

Often times I have experienced that the Y axis of a 3D printer gets bent or broken. ...This part acts as a replacement. You can take the 3D print of this and install it in your 3D printer.This part is of Ender 3 3D printer.

I made the model to adapt it to the ender 3 v1. ...it is part of the Lamborghini Ender 3 pro pack

... To fix this, I added a shim between the motor support bracket and the 40x40 aluminum extrusion for the Y-axis base. ...This allowed me to compensate for the slight bend in the motor support and now my belt stays centered on the pulley at all times.

Spindle Motor mount for Ender 3. Can be attached by replacing hotend of printer. Motor : DC775 12-24V DC spindle motor Motor dimensions 45mm diameter 67mm height. Thanks to RCLifeOn https://www.youtube.com/user/RcLifeOnSimon Origin of the idea :...

Adjustable Motor Mount for Ender 3 or CR10 Simplified. Attain Perfect Leadscrew Alignment with the Motor to Prevent Binding. Easily Adjust the Motor Right or Left, Ensuring It Won't Hit the Bed, Then Use Common Spacers to Fine-Tune the Motor Forward...

Improved Z stepper motor mount for Ender 3 V2. Will let you adjust z stepper motor to the sides about 2mm and it has a 0.5mm spacer behind the stepper motor. You will need some longer screws to mount it to the frame and some short M3 screws to mount...

angle compensation" - the motor is mounted at a slightly larger angle in relation to the model which is to compensate for the inclination after tensioning the belt. - other improvements If anyone has additional suggestions, please write I did not...

Easy modification for the original Y Axis Damper, adds space for the motor damper. The model should be accurate enough to achieve a good fit, but you can add extra washers to the damper/chassis depending on how well the pulley and belt operate. I...

Human: Modified Z Motor Mount Based on Ender 3 Design, Correcting Existing Issues for Enhanced Performance: - The new design allows for adjustable motor positioning by expanding screw hole spacing. - The inner mount has been removed, enabling...

This is a custom motor mount designed specifically for the Ender 3. Engineered to address common issues with Z rod alignment, it boasts an added thickness of 0.8mm, ensuring precise placement and minimizing potential problems. ...Additionally, its...

I remixed two Z-motor mounts, because i realy like Ross_k's design, but also i like ReDaLeRt's mount ( looks stronger ), so i combine them. I print it without suports, 0,2 resolution on my Ender 3, placed like on picture. I Updated step for...

Also design a cover to give it more strenght.Printed on my CR10-SE with Dynalab PETG.You will need some parts to upgrade the motor:1) The screws and t-nuts from the current Y mount and the endstop.2) M3 heat inserts3) M3x8 screws for the steper motor...

This design is based on the design of "Adjustable Z-motor mount for Ender 3 (also Pro) - M3 version by matteeee". What I did : - Make the side part a little shorter, since there was no point on having it longer - Increased the side support to...

Minimum belt size: 670mm (measured and tested) Maximum belt size: 700mm-ish (696mm pictured) BOM: 20T pulley: https://www.amazon.com/dp/B08TV1NF4B 40T pulley: https://www.amazon.com/dp/B07ZKF7G5G Dual Z kit:...

The holder is in the original size according to the original from Creality.Suitable for ender 3 and CR10 printers and their derived variants.Printed without supports.If you are interested in my work, the links are...

Z motor mount bracket that takes care of Z axis screw misalignment. I have modeled this as mine had misalignment that was not solved by shims. This bracket offers 4 mm of slots for motor. My Z axis glides like butter now. 0.2 mm. No supports...

This is a Remix of https://www.thingiverse.com/thing:2920060 and https://www.thingiverse.com/thing:3769941. ... There is no need for screws, the mount just snaps to the extruder motor.

I've also moved to a top-mounted, double lead screw, design (https://www.thingiverse.com/thing:4569498) so do not have a need for this z-axis motor mount any longer. This is a remix of a remix created by Alloca. Original motor mount design by...

This is a mount for large NEMA17 motors. Tested it on 48mm. No additional idler pulley needed. ...This mount is also suitable for wide 9 mm belts and 10 mm pulleys.No supports needed.This is remix of https://www.thingiverse.com/thing:4714828

As for Mounting the Router Bit or Dermal Bit to an R/C Motor, I Haven't Found a Method Yet. I'll Look into That Once I Reach That Stage of Development. The Drone Motor I've Mounted So Far is a Emax RS2205 2300kv Model. The Hole Size Is Perfectly...

This z-axis motor mount is no longer needed for me, but I'll still share it with you. It's a remix of a remix created by Alloca, and the original design was done by Hangtight. I removed the extra spacing material that Alloca added to their specific...

This is a remix of this :https://www.thingiverse.com/thing:2932344 for the Ender 3 v2. I took off the left hand side and also took off the side notch because for some reason it made the z-rod bend to the left looking it behind. ... Follow the...

Another mount for Ender 3 Raspberry Pi Camera Mount (https://www.thingiverse.com/thing:3188580). ... This thing fix the camera on the Y mount axe.

Remixed version with 3mm holes for M3 screws instead of M4. ...And added 45° slope under motor for easier printing without supports. ...Mirror version can be easily made in slicer.

Quick swap time: swapping the mounting holes to fit 5mm screws instead of the smaller 4mm ones I have on hand. All I need are some spare 5mm screws lying around. The hammer nuts required are straightforward - just simple 5mm hammer t-nuts, available...