ender 3 y linear rail 3d models

Endstop adapter STLs for the Funssor/PTCinder/probably other names Y-axis linear rail kit. ...Example listings: https://www.aliexpress.com/item/1005002628710810.html https://www.amazon.ca/PTCinder-Creality-Upgrade-ADAPTERS-Competent/dp/B0B5SZVQ5M/...

I designed this for my Ender 3 Pro with linear rail on y-axis to reduce the vertical ripples and to improve the stiffness in general and to also eliminate some resonances. You can adjust the Z height of the support to fit it in. Could also be...

Yet another Ender 3 Max Y axis linear rail carriage.I've gone over multiple design choices, and this is the last one, everything seemed way too flimsy for the 3 Max bed so I decided to beef it up.If you're going to try it make sure you have clearance...

This is a conversion for MGN12 3 point bed leveling on the Ender 3 Pro and it will also work with the OG Ender 3 and possibly other printers that use a single 2040 or 4040 extrusion for the Y axis. Files are included in iges, step, fusion, and STL...

Had to simply extend the part a bit to fit the holes on the Ender 3 MAX bed carriage, works perfectly

While installing a set of tech drawers (https://www.thingiverse.com/thing:3831119) into my Ender 3's front sections, I found that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer casing. After printing...

While attempting to install a set of tech drawers (https://www.thingiverse.com/thing:3831119) into the front sections of my Ender 3, I discovered that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer...

The modifications include drilling new holes in the Y plate, mounting new rail retainers, relocating the Y-motor mount, front idler assembly, and Y-axis limit switch, and re-tensioning the Y belt. **Analysis:** The document is well-structured and...

# BOM * 1 x Ender-3 * 1 x 300mm MGN12H linear rail * 2 x M4x20mm screws * 2 x [M4 t-nuts](https://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Daps&field-keywords=m4+tnut) * 2 x M4 washers * 12 x M3x8mm screws * 12 x M3 t-nuts * 4 x M3x25mm...

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail2 x M4x20mm screws2 x M4 t-nuts2 x M4 washers4 x M3x25mm screws16 x M3x8mm screws12 x M3 t-nuts4 x M3 locknuts12 x M3...

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail1 x M8x60mm or 1 x 5/16x2-1/4" bolt1 x M8 washer or 5/16" washer1 x M8 locknut or 5/16" locknut2 x M4x20mm screws2 x...

I remixed the bracket from H2FSPawn and Warump because I dont rely on 3D printed threads. ...Therefor I added sink holes for M4 Nuts (connection to bed) and M3 (connection for y-axis stop). ... Hope you like it.

Ender 3 V2 Y-axis dual linear rail I'm using 2x MGN9 linear rail (length 300 mm) 2x MGN9H carriage block stock Ender 3 bed Parts to be printed: 2x mount_single.stl 6x support_plate_rail.stl 1x stop_extension.stl

Simple endstop switch mount for ender 3 with linear rail conversion

When using the original Ender 3's narrow Y axis extrusion with dual linear rails, installing the limit switch becomes a challenge. This simple mount attaches with T Nuts and can slide fore and aft for fine tune adjustments. ... Mount is sized for 2ea...

This is a linear guide alignment tool for the Y Axis of an Ender 3 Pro. I bought the creality kit and they had a guide for the X Gantry and the Z but nothing for the Y Axis? I designed this so you print two of them and it should fit the extrusion...

This is a linear guide alignment tool for the Y Axis of an Ender 3 Pro. I bought the creality kit and they had a guide for the X Gantry and the Z but nothing for the Y Axis? I designed this so you print two of them and it should fit the extrusion...

Ender 3 V2 Neo, Upgarde Linear Rails der Y-Achse.Endblock für den Endschalter Y-Achse mit Langloch zum genauen einstellen.Bei den Umbausätzen aus dem Netz sind keine Maßangaben dabei und man muss schon genau schauen wo genau die Linearschienen hin...

Made a change to the design to take remove mass, keep the build plate at the same height, and make it work with MGN12H and MGN12C rails. ...Uses M5x5.8mm, OD7.1mm thread inserts and 300mm rails

This mounting guides are for the linear rails from AliExpressX axis has a width of 9mm and Y axis is 12 mmLink: https://www.aliexpress.com/item/1005004944650633.html?spm=a2g0o.order_list.order_list_main.5.3f5c1802ayKkvxInstallation:...

You'll require two RA brackets and three small bracing plates to install a single 2020 V-slot linear rail support on an Ender-3 or any printer that utilizes V-slot extrusions.

Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free motion.

... use a very tight/high quality rail for Y. This allows the use of the blue annodized carriage direct onto 2x 300mm 12H linear rails. Edit - more elaborate V2 added. ...Adds some holes for self tappers to increase stiffness, as well as some ribs.

This is a fixed version as the original clashed. ...I could not edit that "Thing" so made another. See a photo of it in use on my Ender Pro with 2x MGH12 Rails.

Even after putting the offset bracket all the way back and removing the lever from the switch my bed was still 4-5 mm short, so I've extended the bracket another 6mm (will reach the corner of the stepper motor)

... the bed, it is simple to mount. I recommend CNC aluminum to make these. Enjoy :D You will need 8x M3 8mm for mount on linear rails 12x M3 8mm for mount linear rails on Y-axis 12x M3 T-nuts 1x M3 10mm 1x M3 nut 4x M5 washer 4x M5 12mm 2x MGN12H 30cm

Drill guide is a good idea, refer from https://www.thingiverse.com/thing:3555147 thanks Domi1988 Drill guide just for drill hole, need't install to machine 钻孔板只是用于钻孔时定位孔距，不需要安装到机器上 This is a remix from https://www.thingiverse.com/thing:398515 Linear...

Ender 3 V2 Y-Axis Linear Rail Bed Carrier Mounts No Drill - this is a remix on one side of someone else's mount that are very very good but left out the Endstop Paddle. Print one of each top side down on the bed. I looked high and low, these are the...

An upgrade to fix the not linear Y Axis extruded bar