ender 3 x y z calibration 3d models

This is a design of the y-carriage that if milled out of 4mm carbon fibre composite, would only weight about 30 grams, which removes a lot of weight from the y axis and in theory allows way higher speed in the y axis This supports 3 different kind of...

This is a design of the y-carriage that if milled out of 4mm carbon fibre composite, would only weight about 30 grams, which removes a lot of weight from the y axis and in theory allows way higher speed in the y axis This supports 3 different kind of...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration.They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto the...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration. They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto...

This is a tensioner for the Y belt on the Ender 3 Pro. My goal was to design this so that it does not require any support and be easily printable. And also to look nice. A slightly less than 30 mm long M4 screw and a nut is needed for assembly. ...

This is for ender 3 v2's inside of an enclosure after the PSU has been moved outside of the enclosure. Requires some long M5 bolts, longer than stock M3 bolt for mounting stock Y axis endstop housing, and some GT2 idler pulleys (one toothed one...

I needed to put my Ender 3 V2 Y-Axis endstop further than it originally is, so I had to remix one I found to achieve that.Keep in mind that the adjustability is not that great, as at some point (unless you modify your Y Stepper mount) your bed will...

You should probably use a drill press for this since it requires more accuracy.On my quest to print at very high speeds on my Ender 3 Pro, I noticed some room for improvement in the Y axis mechanics.The V rollers were inconsistent and unreliable, the...

I'm adding a second Z stepper motor/screw thanks to the Dual Z Axis Ender 3 / 3Pro by CR83D Since I'll be using direct drive extruder I no longer need the original part with extruder mount. In my case it was bent uneven, so the 3d printed part...

SO THIS OBJECT CAN BE USED FOR X AND Y CALIBRATION. ITS 50MM X 50MM SO LARGER AND MORE ACCURATE FOR ADJUSTING X AND Y STEPS/MM THAN THE TYPICAL 20MMX20MM CUBE. Z IS ONLY 10MM IN THE STANDARD VERSION TO MAKE IT QUICKER TO PRINT, BUT I HAVE INCLUDED A...

Building a box frame out of 20mm PVC conduit, needed a joiner.

No description provided.

Human beings are complex creatures, full of contradictions and mysteries waiting to be unraveled. Despite their many flaws, humans possess an uncanny ability to adapt, learn, and grow at a pace that is truly remarkable. From the moment they take...

The individual in question exhibits a complete lack of information regarding their characteristics.

I'm Here to Help You Create High-Quality Content. ...What Do You Need Me to Spin?

The individual in question is devoid of any distinguishing characteristics.

The human form is a wondrous creation, a unique blend of physical and mental attributes that set us apart from other living beings. ...Humans possess a complex array of senses, including sight, sound, touch, taste, and smell, which enable them to...

Adjusting the Y-axis belt tensioner on your Ender 3 Pro just got a whole lot easier with this wedge type tool that makes precise adjustments in 1mm increments a breeze. The clever design keeps the roller axle perfectly straight, ensuring the belt...

These custom-made smoothers were inspired by the flexible tubes on both ends of the X, Y, Z, and Extruder wiring on my Creality Ender 3. My version is an improvement since the label is molded into the plastic instead of printed on. Those pre-made...

This updated piece has greatly stabilized the Ender 3 Y-axis, resulting in a significantly quieter machine. I've printed two of these brackets to mount on either side of the y-axis. ... Here are the hardware components used per bracket: 3x M4 T-nuts...

I made the model to adapt it to the ender 3 v1. ...it is part of the Lamborghini Ender 3 pro pack

Attachment for Ender 3 Enabling Camera Arm by HippieHeadShot (https://www.thingiverse.com/thing:3095730) Connection, Allowing Camera Mount on Y Axis Instead of 2020 Rails. Print Settings: * Supports recommended everywhere with 50-degree overhangs;...

The part below My Ender 3 Max bed wasn't getting enough clearance so the Y axis motor was making a horrid sound at the end of prints. So I sliced off the top of the case and a bit of the slider. The holes on the side were not quite lining up, so...

I loved this mod Ender 3 v2 (and other) Raised Squash Ball Feet by Kamel Makhloufi | Download free STL model | Printables.com but found that at higher print speeds the Y axis wobbled a lot so made up this support bracket to use another mount to...

This is specifically for the Creality Ender 3 Y axis Eazy install and removal. Follow Ryan's instructions for Printing. ...When using, remember that the bed moves to the forward position when complete, so use an arm or two to place your camera out of...

I designed this by using solidworks, You can use the stock of bolt and nut from ender 3 PRO Y belt. Advantages: Anti-electric shock Big diameter get more stronger to tension the belt Cover all rectangle shape of frame make more stable and...

MY TAKE ON THE ENDER 3 S1 PRO Y AXIS MOUNT. ...WIP Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT ...

Specifically tailored for the Creality Ender 3's Y-axis, this module makes installation and removal incredibly easy. To print, simply follow Ryan's clear instructions. ...When using, be mindful that the bed will move forward when complete, so consider...

I was struggling with my Y-Axis stepper damper on the Ender 3. Found a solution: https://www.thingiverse.com/thing:3024360. It worked well but had some flexibility in the bracket. I simply added a 20 mm reinforcement to the side that secures the...

I didn't find a picam mount I liked so I designed one that fits snugly over the Ender 3 y-axis tensioner bolts without requiring disassembly. The field of view is most of the print bed until the y-axis is fully extended, and it clears the axis at...