ender 3 x axis 3d models

This support is designed to be held on the top part of the x-axis frame, not the bottom, as the original STL file wouldn't fit correctly on my Creality Ender 3 Pro. - PiCameraXAxisLeft-4degrees.stl: This model is based on the original but with a...

Ender 3 or Pro X-Axis Belt Tensioner for short belts. The original version was found to be too tight for my belt, so I remixed this one for the tighter belt that my 3D printer has. It only tightens the belt up by an additional ~10mm, but my belt is...

This support is intended to be hold on the upper part of the x axis frame, not on the lower. Because the original stl on a Creality Ender 3 pro, not fit in the correct place. PiCameraXAxisLeft-4degrees.stl : This model is based on the original,...

... and pushing the screws through to offset the motor slightly before tightening the screws holding it in place. All screws and bolts used were items I had on hand after upgrading the extruder, some of which originated from assembling my Ender 3.

Here's my attempt at designing an Ender 3 X motor cover. I'm not exactly the most patient person, so I kept things simple by clipping mine onto the existing cover - no messing with the end switch required. The print was quick and easy. ... There are two...

Webcam holder for Ender 3, which is fixed to the X-axis stepper motor cover. In the plastic cover there is a small cutout on the bottom, where you mount this holder using the included clip. You will need one M3x12 (or longer) screw and nut. The...

Webcam holder for Ender 3, which is fixed to the X-axis stepper motor cover.In the plastic cover there is a small cutout on the bottom, where you mount this holder using the included clip.You will need one M3x12 (or longer) screw and nut.The nut is...

This x axis cover replaces the original black plastic cover for the x axis motor and the mechanical endstop switch attached to it. It has a "bump" attached that functions as an endstop for the hotend-sled when using sensorless homing. ...This cover...

Special thanks go out to Carasibana and Orseeny, who generously shared their incredible talents. ...This book was printed at the finest resolution possible on a crisp 9:00 AM morning using the cutting-edge Ender 3 printer.

I designed this part as a replacement shroud for the x axis stepper pulley in order to move the end stop switch back 4mm. This allows me to utilize the entire 235mm by 235mm bed. With the original endstop mount, 4mm of the bed is not utilized,...

Remixed this X-Axis cover to display a Subaru Tecnica International (STI) logo. There are 2 files (blank background & cover) so you can customize your own colorway for the logo. ...For my example, I used MatterHackers Build PLA Red and SUNLU PLA Silk...

I'm creating a custom x-axis cover that lets me utilize cable chains. If you're looking for compatible direct drive components, I recommend checking out some of the products on my channel for inspiration. ...All credit goes to the brilliant designer who...

First successful print on my Ender 3 Pro using the included white filament, straight out of the box with no modifications made to the original file provided by https://www.thingiverse.com/venegade. It turned out perfectly! ...Thanks to Venegade for the...

This is a remix of the x axis plate for MGN12 linear rail mod by BobbleJot (Thing:3489410).\r\nhttps://www.thingiverse.com/thing:3489410/\r\n\r\nI had a problem attaching the hotend to the plate, just like others who have used this...

I soon realized I didn't need to replace the cap at the left side of the X axis, nor did I need to bolt it onto the stepper motor. ...The weight of the camera is virtually nothing, so the camera mount doesn't require a ton of strength and can simply...

The original Cable Guide worked ok but my new Ender-3 has a problem keeping the cable in the guide plus it always sounded a little "crunchy" sliding the cable in an out even though I can see no real wear on the cable sheath even after nearly 4 years...

This remix of the Creality Ender 3 motor cover is a testament to innovation and design prowess. By utilizing advanced 3D printing techniques and leveraging the capabilities of open-source software, creators can now produce high-quality custom parts...

No additional hardware is needed other than the rail itself and some M3 T-Nuts and bolts: Alignment Jigs and Drill Guides ---------------------------------------- Materials: 1 x 320mm long MGN9H Linear Rail - Aliexpress 1 x 330mm long MGN12H Linear...

I needed a carriage plate adapter for an MGN9 linear rail mod on my Ender 3. While the original was a good starting point, I wanted to be able to add heat set inserts for adding and removing the hotend mount that I use (HeroMe Gen 5). I also needed...

I took three different models and merged them together to create a modified X-axis mount for the Raspberry Pi camera with an HDMI converter board attached. The original housing that came with the mount was designed specifically for just the camera...

This build will allow you to add motor dampers to the Ender 3 (that has non-removable gears) without replacing parts. Things you'll need: 6-12 washers, 2 M3x8 Screws, Superglue (If you do not have washers, you can print 2m high cylinders, but it...

Modification of the x Motor Cover with Magnet Support Works Seamlessly on Mi Touch Devices.

I reworked the design by removing the hex nut recesses since they appeared to be an unnecessary weak point, which is where my original failed along the bolt axis. ...Additionally, I incorporated a couple of thin shim washers to close the gap and match...

Well alright, what we have here is a purely cosmetic piece.. It serves no purpose other than to look cool compared to the stock QR sticker in the location in question.. That being said I designed the part to just clip on the housing so you can print...

Well alright, what we have here is a purely cosmetic piece.. It serves no purpose other than to look cool compared to the stock QR sticker in the location in question.. That being said I designed the part to just clip on the housing so you can print...

This thing was crafted with Tinkercad and can be edited online at https://www.tinkercad.com/things/8pd7ItHCAjF. A slight modification was made to a related design on https://www.thingiverse.com/thing:3270228. The original design had one issue - it...

Display the colors of our mighty horde on a proud banner!

A user uploaded a 3D model to Thingiverse, specifically design 3758125.

I'm obsessed with the Imperial cover design, but it lacked a matching element - the Extruder knob and fan cover didn't quite fit in. ...So, I cleverly combined them into one seamless unit.