ender 3 x axis 3d models

Remixed Ender 3 X- axis stepper cover. ...Done with the cutout profile of a Saturn 5 launch (second picture is reference) Also added a lunar lander and module from https://www.thingiverse.com/thing:3758364 for a nice touch (scaled at 130%)

Remixed Ender 3 X- axis stepper cover. ...Done with the cutout profile of a Saturn 5 launch (second picture is reference) Also added a lunar lander and module from https://www.thingiverse.com/thing:3758364 for a nice touch (scaled at 130%) Print...

The purpose of it is to replace the original part of my Ender 3 v2, which over time gave way and broke, cracking. I simplified some parts, since in the original, being manufactured by injection, some details are complex. In this version, partitions...

I found a lot of PiCam mounts for Ender 3 (Pro), but none of them suited all my needs: - close to the left hand side of the printer, so that my 50cm ribbon cable is sufficiently long - Moving with the z-axis - Simple fixation on the printer without...

3d printable parts to upgrade ender 3 x axis with 250mm ball bearing linear rail and improved duct. Compact design with cable management groove, 40mm fans housing and bl-touch bracket. Perfect to have a clean setup with an accurate and sturdy x...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

You will only need - this bracket - one 300mm linear rail linear rails MGN12C (15mm x 20mm) or MGN12H (20mm x 20mm) - 4x M3 countersunk screws - 2x or 4x M3 threaded standoffs Works great with @whistleblower's Ender 3 V2 Fan Duct for 5015 Part...

couldnt find this so i created it. ...this is the x axis cover for the belt tensioner on the Ender 3 V2 NEO (only!)Printed at0.16mmPLAScrew mount side up on plater

This part was remixed specifically an early version of the Befenybay Direct Drive X-Axis Cable Chain on the Ender 3 3D Printer. Amazon Ean#: 0705300791787 The x-axis direct drive bracket has 2 wheels on top farther apart then the Micro Swiss Direct...

Unfortunately, the x-axis clip that Beh01der created was not compatible with my ender 3 v2 neo. The (very) crude modifications I made to Beh01der's design include a notch on one of the clips to clear a mounting clip from the shroud, repositioning a...

This plate screws onto the housing for the x-axis home switch on an Ender 3. Made to work with stock screws. Supports needed for the sword only, I printed the sword upright supporting the handle to ensure a clean blade surface. ... The sword is the...

It's made to press fit over the X Axis bracket and belt cover on the right hand side of the printer while leaving access to the belt tensioner knob.  You'll need a screw to mount the camera with, I used this one:...

Since it's attached to the X-Axis, the print area will stay lit all the time without adding weight to the print head as the Z-screw raises. Two prints should support most 5050 LED strips, including WS2812/Neopixel addressable LEDs. The compact...

The first modification I made on my Ender 3 V2 was to add led lighting on the top, but this produced shadows with the X-axis and fuser block on the parts. I improved that same design I did the first time so that it could be inserted on the opposite...

 Simply print each of the model files (making two copies of the bolt and nuts) and slip the printer_cap over your printer's x-axis.Credits ( Please Retain on Derivative Works)This model was remixed from the camera mount work by mfraz74 and the...

A Simple C270 X-Axis Mount for the Ender 3 V3 SE Used the mount I use for the Ender 2 Pro and remixed it for the Ender 3 V3 SE, the clip is great for the C270 if you don't want to remove the clamp it comes with. I printed it using 0.2 layer height...

I wasn't satisfied with the side mounted linear rail designs shown on most Ender 3's. Here is my design of a top mounted linear rail with 3D printable brackets. Below are links to the parts I used. I used M3 hardware for this entire build. ...

X axis linear rail conversion for the Ender 3 replaces traditional carriage with a custom printed one, utilizing a new belt attachment system that eliminates the need for drilling. The top V-slot wheel mounts are repurposed to provide a sturdy...

Positions x axis switch to allow MGN12 carriage to home. ...Works with the XChange system

tensioner for X and Y axes of ender 3 printers and the like diameter for 4mm profile screws diameter for 4mm pulley screw joints of the pieces with 3mm screws tension bolt diameter 5mm - V2 pulley bracket: The pulley bracket bore has been corrected...

BOM: 1x 608ZZ Bearing (very common, used in things like skateboard wheels) 1x M4x16mm Bolt 2x Cable Tie Parts to Print: 1x X-Axis_Cover.stl 1x Cable_Mount.stl 2x Bearing_Adapter.stl Assembly: - Put the bearing adapters inside of the hole of the...

I needed this solution because I changed the gantry carriage to the one used on a standard Ender 3 V2 because I wanted to use the Minimus hotend fan shroud by Rogue Paul. But the stock endstop doesn't get bumped with this carriage. Just reuse the...

This is a webcam mount that replaces the plastic end cap of the x-axis. unscrew the existing cap and put this on instead. any webcams that has a screw hole on the bottom can be mounted upside down. ...the width of the slot is 6mm.My webcam is about 52...

This remix incorporates my own X axis linear rail conversion design, tailored specifically for Hangtight's design at Thingiverse: https://www.thingiverse.com/thing:3594559. One of the screws holding the extruder bracket has been modified to pass...

So I found out the hard way that if you tighten your X belt too hard the cover will break…This is a more solid replacement part which I printed in 0.12mm with a 50% fill.I hope it helps more people.

On-Axis Camera Support for Ender 3 S1 Plus.The support is fitted and screwed onto the X-axis adjustment cover, robust, rigid, the camera remains firm and still.Printed in PETG Gcode file with all parameters for printing. Supporto Videocamera su Asse...

Inspired by d4t4b's Ender 3 X-axis cable router, a remix of johnniewhiskey's Ender 3 Cable Chain and FedorSosnin's Stock Ender 3 & A10 Hot End Chain Links is created to guide hot end cables to the front and add cable chains. ...This part can be attached...