ender 3 x axis limit switch 3d models

Remixed it so it hides the pulley 2 versions, with hex and without hex stepper motor cover here https://www.thingiverse.com/thing:4551033

<p>I wasn't a fan of the QR code on the printer. ... A few remixes later, and I had this part.</p> <p>After removing the QR code (it's just a sticker and it came right off), I applied a little glue from a glue stick (I know you have one laying around,...

I didn't want to extend the wires so I used the hot end mount and remixed it as well as the extruder mount from the slim cable chain design by norp which I also remixed. The current rendition has two cable chain sizes with a combined special link to...

It is a modification part designed for protection against dust. Imagining an original design and turning it into a solid model using the drawing method is a more arduous process than expected. If this design is a functional object, technical...

This is a remix, check out the original! I wasn't sold on the QR code on the printer - it was just a sticker that came off easily. I tracked down the original design but wanted only the front panel, so I removed the three sides. ...After taking off the...

I'm building a fast setup for attaching an IR camera to a Raspberry Pi, which is synchronized with my 3D printer's hotend. ...Further details and images will be added later.

This creation was crafted using Tinkercad's user-friendly interface. ...To edit or modify this design, simply visit the official Tinkercad website at https://www.tinkercad.com and navigate to the specific thing identified by eODlAKV1aiX.

Yet, it became clear that someone had made an adjustment between production runs, affecting the new x-limit switch. This switch no longer contacted the stop plate when trying to find home. Using binder clips and lab tape for six months resulted in...

This is a modify of **Shutdown switch ENDER 3 by fafabienman** https://www.thingiverse.com/thing:3517641 I created this remix because in the original, not very convenient mounting of the switch stick. In the remix, the switch stick consists of two...

Unable to locate an NC 3-way toggle switch, I opted for a NO circuit instead, understanding that it's a trade-off between two potential risks - metal chips potentially entering the housing and causing the NC rig to fail closed, or any internal...

z-axis stabilizer bracket, designed to accommodate 2 F684ZZ Flanged Bearing 4x9x4mm. ...If you have put a x-axis tensioner on your printer you can use the extra hardware and bearings to install the stabilizer. ...

The stock part mounts directly to the right side of the X gantry, providing vital support for the vertical axis and ensuring overall stability.

This x-axis cable holder screws on to the ender 5 x-axis motor plate, and prevents the x-axis cable from pinching. Also, there is an additional cable support for the main harness in order to prevent it from rubbing against the frame. ...(see attached...

Installing x-axis linear rail requires moving the limit switch, most covers required getting new longer screws to attach the new taller cover. ... This has recessed screw holes so you can use the existing screws.

... guide (https://www.thingiverse.com/thing:3015832), so you can use them without modification. Parts required: 1 x Z-axis guide 1 x ID 8mm OD 22mm (608) bearing 4 x M3 12mm screws 2 x M3 washers to secure the bearing 2 x M3 nuts 2 x M3 T-nuts

Lock your Z axis for changing filament or while transporting. The 2 holes are not threaded, but meant for M4 tap. ... 2 screws, M4 X 12 are used to connect the 2 pieces.

Here is the spun version of the original text: New X Axis Mount with effortless motor extraction and cable management points are included. ... V2.50 Rough prototype, unverified, still under development

These objects replace the original z-axis micro-switch holder. If your plate is calibrated but too close or far from the nozzle, you can try moving all the plate wheels, but be aware that this might ruin the calibration. A better solution is to move...

I modified the bracket from the original design here: https://www.thingiverse.com/thing:2757810 to fit the Ender-3 printer by shortening it in Blender using the STL file. To assemble, you'll need to print nine link_top.stl parts and nine...

The filament run-out switch I bought (see below) did not fit so I designed a case that fits the Ender 3 Z-axis, using only the switch and wiring. Search Amazon - SIENOC 1.75mm 3D Filament Detection Module Filament Run-out Pause Detecting Monitor...

My version of the silent limit switch casings for the Ender 5 printer, inspired by [Silent Auto Home for Ender-5](https://www.thingiverse.com/thing:3349425), but rebuilt from scratch. They make use of the original limit switches but you may need to...

it does work for a broken tab or a tab-less switch.Make sure your filament isn't too brittleDesigned for a 0.4mm nozzleI made this for someone else so I personally have never printed it but he said it works for homing his E3pro printerV1 is thin and...

I built an adapter to lift my Z-axis carriage plate above the Z-axis stepper motor so it clears.

I needed to print this part to be able to use my belt tensioner when I attached the linear rails for the Ender 3 by funssor. They have apparently not tested these before selling them. Hope this helps someone! ... This is a remix from the awesome design...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

I mounted the ender 3 v2 in an ikea lack, with the power supply outside the enclosure, so I needed to have the switch accessible in front part.

See Also: Ender 3 X Gantry Mounted LED Light Strip Mount: https://www.thingiverse.com/thing:3367976 Ender 3 Hot End Mounted LED Light Strip Mount: https://www.thingiverse.com/thing:3368179 Ender 3 LED Light Strip Cable Clip:...

The Z-axis Test 1 utilizes materials from the Model LM8UU.

Reminder for the movement of the Nozzle up or down (Z-Axis)