ender 3 won't turn on 3d models

Universal spool support for Ender 3.I repositioned the spool bracket on my Ender 3v2 for a smoother flow of the filament. Therefore i build a new spool axis with two bearings. I used bearings without gaskets. ...No further guiding needed.(Also see Ender...

I designed this as the others dont fit the latest Ender 3 pro or the they dont fit with a Ender sitting on a table without any dampening (mines as is from the box sitting on a table) Ender 3 pro draw. Unscrew the control board and slide draw into...

I'm not entirely sure if it will work on the Ender-2 since I don't have one to test it on, but feel free to try it out and share your experience with others. The guide was printed in yellow to make it stand out in the picture, but I'm re-printing it...

Don't Tread On Me stencil

Don't thread on me stencil

The file in 3Ds Max 2017 and can be opened in any compatible packages format FBX. ...Set consists of 3 t-shirts on hanger. Textures in format JPG. ...Seams are made with a mask using displacement.

Printing with the stock Ender 3 fan duct should be sufficient, but I highly recommend reprinting with this ring duct installed for better print quality, especially on the inside surfaces. This design is specifically tailored for the newer Ender 3...

Boo's Ender-3 Nightshade, I set out to create my own unique version, the Blank Ender-3 Nightshade. My goal was clear: eliminate any visible logos and branding, resulting in a sleek, unadulterated printer. Printing the Blank Ender-3 Nightshade flat...

I wanted to raise my Ender-3 off of my carpet but I couldn't find a basic solution so I designed these standoffs/feet that slide into the double T-slot aluminum extrusions.

Required to create M5 threaded holes on the 20x20 rail of the Ender 3. 1 - Pi controllable relay - https://www.amazon.com/gp/product/B082S47JXM/ref=ppx_yo_dt_b_asin_title_o06_s01 1 - C14 Inlet Module Connector Male Power Socket with Switch -...

This is a basic standalone tool holder for my Ender 3 printer. The clipper holder is designed as a separate piece for easy printing, allowing users to rotate the pin vertical with ease. Allen Key spaces feature dips that keep them facing outward,...

I'm adding a tramming plaque to my Ender 3, a friendly reminder of how to turn the wheels. A nod to all those trips to the Jersey Shore Boardwalks... "Watch the tram car, Please". I print with a layer height of .18 and use tree supports, although...

Sharing my design for a pair of Creality Ender 3 Dustfilters that I'm excited to share with you. Made up of two parts, the top and bottom components are fully magnetic, ensuring they stick together perfectly. To attach the magnets, I used superglue...

I made these for my Ender 3 Max, but they also fit on the Ender 3 Pro and the original Ender I believe. Not sure about how they fit on the V2, but someone should try. Added a few 3mm nuts and bolts and had to use a longer 10pin Display cable and a...

The bolts may not be long enough, but if you have just a single thread on the t-bolt, you can manage to get it into place and tighten it down (at least with my Ender 3 setup). This is my first upload, so please be kind. Thanks! Modified the original...

The walls of similar prints were too thin for my preference. Might be a little to long depending on the knob used on the display.Nothing fancy or complicated.I used 50% infill to but definitely isn't needed.supports - NOBrim - NoMade with...

I used a similar design found on Thingiverse, but it was too high for my liking, and I didn't like the square base either. Print this foot flat on the bed with threads facing upwards. ...It prints without support, but the base requires support from...

... glove. ...They elevate the Ender 3 by approximately five-eighths of an inch, raising it off the ground. A slight indentation on the underside of each foot enables users to incorporate the pre-installed rubber grips found on the bottom of the printer.

I've been wrestling with finding a reliable PiCam mount for my Ender 3 that doesn't compromise on weight by relying on the z-axis. This led me to discover two promising files: https://www.thingiverse.com/thing:3014982 (PLG_Design) and...

Ender 3 Spool Holder Mount Adapter Requires No Additional Screws or Nuts. ...Compatibility May Vary Depending on Your Printer's Extruded Aluminum Frame.

Hello, I built a cable organizer for an aluminum extruder used on the Ender 3. It's straightforward yet very helpful. ...Enjoy!

Guide for filament for ender 3 printer. ...With this guide, the filament will separate on the side and you will prevent the filament from breaking.

Direct with Titan extruder and E3D hotend on ENDER 3. I used pancake motor but can you use normal NEMA17. ...I use retraction 1.2mm

A durable clamp designed specifically for the Ender-3 printer is necessary to securely attach metal extrusions on any side, utilizing threaded screws.

Because of the poor support from creality and my broken cableclip on the ender 3 S1, i redesigned the original cable clip. ... Printed with PLA+ it should work ;)

Snap-on spatula holder engineered specifically for Ender 3 power supply compatibility, requiring a 1% reduction in model scale for optimal fitment.

Made this to replace the broken lever on my ender 3, remix if necessary. ... You will need to reuse the brass inserts in the original part

Remix for ender 3 better fitcheck me out on tinkercad: https://www.tinkercad.com/users/3Np2zyNODHC?category=tinkercad&sort=likes&view_mode=default

Design to cover the LCD on my Ender 3. Leaves a small gap around the LCD for ease of placement. ... Use supports for the center grip.

I modified the clip at the end of this to secure tighter on my Ender 3 Pro's original metal plate.