ender 3 v2 vs pro 3d models
830451 3d models found related to ender 3 v2 vs pro.
prusaprinters
27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...
thingiverse
27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a...
thingiverse
Remix Of VortexPC's MinionD To Fit With Spider 3.0 High Temp High Flow Hotend I Printed in PLA Fan Side On Build Plate With Organic Supports (PETG might Be Best But No Issues So Far) https://www.thingiverse.com/thing:4819097
thingiverse
REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...
thingiverse
Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine
thingiverse
Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile
thingiverse
I got tired of using a ruler to measure each side of the x gantry to see if it was level. These are rulers to place inside the extrusion on each side of the bed, on top of two smaller vslot covers that should measure just enough to get from the...
thingiverse
This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
thingiverse
Top filament sensor all push fit with gap at back for wiring, made from micro roller lever switch KW12-3 and 608zz bearing. See picture for wiring to sensor (pin 1 and 2 on the board) (outer pins for the switch) Top filament cutter with a drawer...
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
thingiverse
This is an improved version (in my opinion) based on "Creality (Ender 3) Filament holder 80mm spools" by mjoaris November 11, 2018 https://www.thingiverse.com/thing:3209211 I designed this with printability in mind - no supports needed and fast...
cults3d
This is an improved version (in my opinion) based on "Creality (Ender 3) Filament holder 80mm spools" by mjoaris November 11, 2018 https://www.thingiverse.com/thing:3209211 I designed this with printability in mind - no supports needed and fast...
thingiverse
Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports
thingiverse
Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.
thingiverse
Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...
thingiverse
... ;Begin Purge Line G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line ;End Purge Line . ..
cults3d
;Begin Purge Line G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line ;End Purge Line . .. ......
thingiverse
To prevent the filament from touching the threaded rod. ... My first part in 3D printing, just after receiving the Ender 3 Pro. I hope it's also compatible with Ender 3 and Ender 3 V2.