ender 3 v2 vs ender 3 neo 3d models

Included is a ready-made gcode for Ender 3 V2 temp tower for PETG. E-Steps are set for my extruder, change line 21 in G-Code to your extruder's E-Steps.Comment out line 20 if you don't have BLTouch/CRTouch.

Hotend cover for Ender 3 V2, printed for reason to replace standard cover and fan. Can mount 60x60 fans with dirrerent width. Mount with three standatd M3 screws and need one M3 nut. ... Need some hand work to align with roller M10 nut.

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

I wanted to make My Ender 3 v2's z axis double. So i needed a part that hold second Z axis motor. This is the original parts 3D design. ... You can write me if you want to improve the parts.

This is a Snap on Holder to attach a Dial Indicator to the Ender 3 V2. It is compatible with BL Touch and helps fine tuning the bed level. ... An M5x12 mm bolt is required to attach the Dial Indicator to the Holder.

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. ... <strong>Probe offset: X-42.00 Y-10.00</strong> <strong>Thanks to...

wire support for my ender 3 v2 direct drive, mounted to the top of the enclosure and use a auto retract keychain inside. ... https://www.amazon.co.uk/gp/product/B0995YK84C/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 key chain used, just trim the...

BL-Touch mount for the Ender 3 V2. I made four version, two round screw and two nut head screw version. The print is support free. Probe offset for the firmware: X = -42, Y = -10 Z-offset is -0.96 for me. ... Additional parts needed : M3x6...

Remixed By Mythical Now supports Ender 3 V2 Changes to the original - Leaves a small space at the back right of the part for the z axis cable that goes into the motor (see picture) Spaced back so the print is flush with the back of the z axis switch...

A replacement knob for the belt tensioners of the Ender 3 V2. Or just an M4 knob for anything ;) Requires a M4 melting winding brass insert (see image) using a soldering iron. ... You might have to open the hole a bit after inserting the insert...

Just a simple belt tensioner wheel redesign for the ender 3 v2 since I didn't like the default blue ones. It works with a M4 nut inside. The tolerances might be too tight in this case don't hesitate to force it inside or even hammer it a little. ...

Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify

I really liked the big rollers for the Ender 3 V2 filament guide, but I needed a more flexible setup where my spool holder could be mounted on the side of the printer, needing a double roller setup. ... (Use the bearing guide/rollers from the original...

I combined this with a mount to attach it to my side rails on my Ender 3 v2. ... I installed it on the left side of my printer, you'll need to remove the 2 fronts (LARGE) screws and 1 screw at the bottom.

Just another filament guide for all Ender 3 models including Pro & V2. Looks similar to the existing guides like 3059604 from MattEllison, but this one slides smooth into place and rests flat on the top rail. To ensure proper printing you should...

Ender 3 V2 better Motherboard Case This motherboard case has a sliding lid that is on the top of it, in this case there is enough room to fit the motherboard and two buck converters for noctua fans or anything if there is anything to update on the...

This is a Camera Arm for the Ender 3 v2 Printer. I am pretty sure it works on other printers, but if it doesn't, lmk in comments, and I will make a version for them! Have a great day! ... copyright Ben Walker

Fits perfect around the powersupply of the Creality Ender 3 V2. You can find the cablechain made by NG_Design here: https://www.thingiverse.com/thing:3769941 Update 1: Made the solid block holding the chain hollow. This gives the cable little...

With these parts you can install any 120mm Fan over your Creality Ender 3 v2 PSU and any 60mm Fan over your Mainboard. ...Fans will be mounted outside of Chassis, so you will need to print 4 of the included 30mm feet.

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle...

... .. ...the stock ender 3 v2 spool holder is a friction monster and causes all kinds of under-extrusion problems. So here is my Brachiosaur-like spool-holder that uses 2 skate bearings. Works well for me. Hope you like it. ...Will be uploading pics soon.

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. //edit: Makers stated, that PLA will work without issues, thanks for...

Tool Holder based on Mattwall model and designed to install in left side of Ender 3 V2. It include slots for screw driver, and fixed wrenchs than come with the printer. ...Additional slot was added to include a gauge thickness to calibrate the level in ...

#### CR Touch Mount for the Satsana Remix for the Ender 3 V2 I couldn't find a remix for the CR-Touch so I created it myself. #### Why? ... Because the original mount didn't have room for the connector of the CR-Touch, and if you tried to put the...

This is a belt tensioner for the Ender 3-V2, made to match the style of the original factory knob. To install, you will need a metric M4 nut for each tensioner. ... The nuts will need to fit these dimensions: x_diameter - 6.8 mm y_diameter -...

... with the Aquila. ...I think the Ender 3 V2 has similar ones. Found the file at https://www.thingiverse.com/thing:4737883. ... It printed great, but I wanted a slightly tighter fit and I made the slope steeper to the tools aligned closer together.

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

This is an adapter to be used with the original spool holder of Ender 3 V2. I have limited space above the 3D printer where the original holder is fixed. So, this thing could be used together original holder over a table. ...I'm using beside de...

This is a remix of the OEM Ender 3 V2 mount for the EZALE Pro large sensor from TH3DStudio. With my machine the original version of the mount covered the adjustment screw making it difficult to adjust easily. ... This version creates a recess for the...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle out...