ender 3 v2 vs ender 3 neo 3d models

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4mrIXgKXpb2

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4mrIXgKXpb2

A small clip that makes uses of the extrusion clamp to keep a PFTE tube (1.75mm) in place. ...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4mrIXgKXpb2

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4mrIXgKXpb2

Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4mrIXgKXpb2

Another version of the same filament guide where the funnel is much closer to the extruder.

Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.

Instead of using washers I designed a 3mm spacer to go behind the backing plate.

Model without inside bearing and bolt

It's my first modeling and it's a terrible skill, but I'm using it well. ...I'd really appreciate it if you could tell me what's wrong or what to improve

Just another filament guide. slip on, so no need for any tools or bearings. ...print without support, and put in place

I just wanted the Z axis bearing , so i chopped off the other bits mounted upside down for it to fit , so results may vary support to build plate is all thats needed ADDITIONAL MATERIAL 1x 608zz bearing 8x22x7mm ...

REMIX OF REMIX REMIXTIME

I made a CAD file using the printed parts and a caliper. I increased the height of the base piece by 8.5mm so it will contact my X-carriage plate. The original height was approximately 21.5mm, so the new height is 30mm. Fillets are an...

I was searching a simple and easy duct for 5015 blower upgrade, lot of complicated designs out there. So I designed my own. It uses stock screw and attachments, doesn't mess with heat cartridge wires, and you have room to regulate distance from...

Filament guide. ...Requires the removal and install off 2 screws on the extruder.

I loved this design but the scraper jingled against the gantry while printing. I added a triangle to the bottom to hold the metal blade away from the gantry upright. Printed in about 30 minutes. Update 08/04/2023 I oriented the print file...

This is an easy-to-print storage tray for an Octopi - tested to fit a Raspberry Pi Model 3b. ...No support should be necessary printing from the face down.

<p>It's a remix of the model by Mattwall</p><p><a href="https://www.thingiverse.com/thing:3877505">https://www.thingiverse.com/thing:3877505</a></p><p>&nbsp;</p>

You will need 8 pcs. It's flush with the surface. It prints fast and uses very little material. ...You don't have to disassemble anything to put it in place.

This putty holder can be attached to the rame. LxWxH: 45.5x24x45 mm For max. ...putty width: 37.5 mm

A switchbox with two ways to insert wires. One through holes in the V-Slot Mount, and the other through the centre of the aluminium extrusion. I also added grooves where you can glue a customisable tag to label the switches. You will need four M3x4mm...

I remixed the robot cover to be able to use with out threaded inserts, I also chopped off the antenna to make print easier and look better. ...Also a couple other things to make for less supports.

I mounted the ender 3 v2 in an ikea lack, with the power supply outside the enclosure, so I needed to have the switch accessible in front part.

Holds thumb drive adaptor, cutters and glue stick Made for the ender 3 v2 but may fit many others Made to clear a duel Z axis motor upgrade

Quick design for a MK8 nozzle holder that fits in the tools drawer for the Ender 3 V2. ...It holds 18 nozzles.

i drew this up in autocad 2020 to relocate my control panel on my ender 3 v2. ... requires 4 M3 x 8mm Cap Screws.