ender 3 v2 thermal runaway 3d models

I designed a MK8 nozzle holder that makes use of the small compartment inside the Ender 3 V2 drawer. It is designed so it can printed without supports. It is printed face down, with basic cura settings it only takes about 2 hours. The main...

In my eyes, this is a decent-looking display cover for the Ender 3 V2 3D printer that prevents both dust from getting on the screen, and light from getting out when it's not wanted. It's slightly inspired by Forerunner architecture from Halo. ...The...

I just got an Ender 3 V2 (my first 3d printer) and I still don't have a home for it and I've been keeping it where it's somewhat easy for my 2-yo to reach and play with the knob (I plan to find a safe place around my house for the printer). So i...

I designed it and used it with satisfaction on my Creality Ender 3 V2. They absorbe the X and Y action (which creates the most thumping movement sound) -The height allows for better airflow underneath the printer. -The balls allow for better...

This rack is designed to fit into the side slots on an Ender 3 V2 Neo. It may fit other models, but I can't guarantee that.It holds the tools that don't fit into the provided drawer, namely the scraper and nippers. It also has slots to hold a small...

''I had enough of the tools rattling each time i would open the drawer and getting all mixed up after i organised them.'' Drawer organiser for the Ender 3 V2: -Will hold all allen/hex keys, wrenches, original bed clamps, 7mm capacity paper clamps and...

Mixup of the Voron Trident skirting and tops for the ender 3 v2.The logo's can be hard to press in a bit of heat goes a long way to helping.Make sure to print the 4 extension feet and use your stock rubbers.I just glued on the “dummy” front feet….

... the mount in place of the larger idler wheel mount screw. I believe they are m2.5x0.45 screws. I used the wiring guide and configuration/firmware found here: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to...

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this so I created my own. I designed a screen cover that uses a hinge system allowing users to open and close it whenever needed. The main purpose was to...

This is my remix of Satsana 5015 Fan Duct that could be used on ender 3 v2 I've used Fan 4010 but 4020 will work too. I highly recomend to go something low db and good m3/h speed. Maybe I will consider noctua for that one in future. Recomendation...

Unlike the original version, this designed for rear placement (next to ender 3 v2 display on the same side). Added small lockers on the rails, so it's fit tight - be careful during installation and not smash it. Nothing really special in terms of...

This is a handle designed for the Ender-3 v2 bed. The front two bed fasteners pass through the two holes on the handle and the springs rest in the counter bore/ slots. The locknuts go on the under-side and hold the handle in place. The arches...

I have an Ender 3 v2 and I didn't want to obstruct the tool drawer or rely on the bottom left groove only, so I remixed darkpoet's excellent design to utilize the left corner. Also I maintained the angle of the holder, but I made the piece flat...

I designed this simple pen holder for ender 3 v2. It's very easy to install. You need to use super glue/hot glue to mount first part to the printer (it can be at a slight angle to the nozzle), then you have to put a pen/marker in a second part and...

#Description The Ender 3 V2 control board is mounted a upside down from the previous Ender 3's, so it is accessed by removing the bottom panel of the surrounding shell.as opposed to the top panel on previous Enders. This makes for a harrowing...

I bought one of those "cheap" "3DTouch" devices which claimed to suit the Ender 3 V2. The correct mount (and the cable supplied) doesn't fit the V2. You can cut and drill the supplied mount and it will fit but my supplied 3DTouch is a bit longer...

If you have any suggestions for improvement or want to communicate with me, please visit my development community and leave a message, I will reply you as soon as possible:...

This is a LCD cover for Creality Ender V2. It is very simple design. ...If you are not sure about your bed leveling setting, I would recommend you to use Brim while printing.

Unitl I found this model: https://www.thingiverse.com/thing:2552992 I liked the idea of this mount and changed it so it would fit on the rails of my Ender 3 V2. This is my first model ever edited/created, so every feedback is welcome. I put 2...

The fan bulge protrudes 8mm below the power supply, and your Ender 3 v2 has 12mm of under-side space available. This makes it a tight fit with just 4mm of space for air to travel through. After careful consideration, I positioned my fan to blow air...

This is a simple print station for an Ender 3 V2, it uses pieces of window wiper to clean the nozzle in 3 directions. To use: Cut 3 sections of window wiper or other heat resistant material into 10mm x 20mm pieces and hot glue them into the holes. ... ...

... knife/scraper thing. Mine simply has a flat plastic piece that attaches to the blade, so I widened and deepened the slot and removed the curve from the original design. In the end the tool holder fits all the tools that came with my Ender 3 v2.

Compatible with "Fillament Guide simple" by WalleYYY https://www.thingiverse.com/thing:4930922 Compatible with "Ender 3 / CR-10 Z-Axis Manual Adjustment Knob" by 3nderlab https://www.thingiverse.com/thing:4299772 and similar manual zAxis adjustment...

These are 2 simple stands that snap onto the 20mm and 40mm profiles on your ender 3 V2 printer. Might work on other similar models as well. Simply print 2 of the wide models and 1 of the narrow, remove the display and snap the stands on the printer...

#### RIBBON CABLE MAY BE TOO SHORT TO BE USEABLE #### #### Very Close to Y-AXIS #### This is a screen mount I designed for the Ender-3 V2. I wanted to be able to adjust the angle of the screen to be seen more directly to where I work from. The mount...

You will need to print with supports, the current design suits standard Ender 3 V2 and also has a cutout for the mounting screw if you have a fang. (refer to .stl - photo shows V1 with smaller cutout) To use this simply lift the Z Axis to 120mm,...

... it holds up, but so far so good... There are apparently 2 versions of the Ender 3 V2 - One of the versions does not have the mounting holes that this attaches to, so... ...:/ The nozzle to probe offset I'm using with this is X-40, Y-7

So i got sick of my guide that i printed off here falling off when using my sunlu filament dryer so i made my own that bolts to the gantry of my Ender 3 V2. No extra parts needed, bolts onto gantry roller nut. I find its still easy to load filament...

This is a (to the best of my abilities) a complete model of the Creality Ender 3 V2, that can be downloaded and edited. The goal of which to allow a user to design parts and test for the physical machine. To my knowledge all of the parts should be...