ender 3 v2 spool holder 3d models

This adapter fits to creality ender 3 v2 stock spool holder to easily rotate filament spools with 56mm or 54mm mounting diameter. ...Two STL files include with 56mm and 54mm adapters.

Adds convenience to changing filament without having to disassemble each spool when changing color.Change the old reel holder magic for this improvement, reusing the grip knob.On the other hand, it can be used to improve 2 independent extruders and a...

mod for original spool holder and my feet 35mm 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596 https://www.thingiverse.com/thing:4684550 fan 60x60x25 noctua fan grid...

With this thing you can mount the original Spool-holder on the printer. ...Usefull if you are using a direct extruder

... ... I remixed it to use it on my Ender 3 v2, added some material on the screw hole so it can be mounted securely with a M4 x 45 screw. It´s tested and it works as intended. ... Printed it at 0.3 resolution and 0.2 with supports and 90% infill.

I have twaeked the design to be a little less filament hungy and to need hexagonal nuts rather than the ender nuts that fit into the extrusion. ... The attachment slides easily into the frame of the printer and positions the spool a little farther away...

... ... https://www.thingiverse.com/thing:4904382 This bracket includes a 3D printable pin instead of having to use a screw and nut however the hole on the spool holder must either be sized to 3/16" or can be drilled out using a 3/16" drill bit. ...

This is an updated filament spool holder bracket for the side spool arm below: https://www.thingiverse.com/thing:4904382 The screw hole on arm at the above link will need to be drilled out slightly to accommodate the 3d printed pin on this model. ...

https://amzn.to/35Jgnc2 However, the spools don't fit on the stock Ender-3 V2 spool holder--the hole is too small. If only I had a 3D printer. WAIT - I do, I do have a 3D printer. So I picked up a cheap 1KG spool (which fits the stock spool holder),...

I created a cheap enclosure for my Ender 3 V2 using exercise foam tiles. Because they're so flexible, I could not place the spool on top as most do with a Lack enclosure. Also, Since I used the original wiring for the electronics, I was limited to...

I was looking for a filament spool holder for my Ender 3 S1 to keep the spool centered during prints. I couldn't find one like I was looking so I've designed this one. Also works for Ender 3 v2 (I don't know about other versions though). This a...

I needed a spool holder that reduced slack on the spool, allowed for different inner diameter spools, AND prevented the spool from falling off completely when tipping or moving the printer. A few hours later, and here we are! Note: Designed to fit...

Spinning Spool Holder for Ender 3 V2, using parts that come with printer Allows the spool to spin freely, preventing issues with heavier spools being unable to feed into the extruder correctly Requires a 150mm M8 Bolt, 1 M8 Washer, 5 Nuts (Preferably...

I also made it so the stock spool holder couldn't slide out of the slot on the holder. There are 2 nuts or knobs. Its dealers choice, both work with the threads. The nut or knob wants to print with supports, but I just blocked them. The Base...

This is a universal-fit spool holder that attaches directly into the original Ender 3 V2 spool holder bracket, with option supports and no external components! The thread is a 1 inch thread and has 3 start locations for the cones to slide along, and...

Just a Side Spool Holder is designed for the Ender 3 V2 because I didn't like the Spool being on top. Doesn't require any screws. It also also almost the exact width of a 1kg spool so it cuts down on side to side movement that the creality spool...

Spool holder for ender 3 v2 holds only 1 kg spool. Has holes for 2, 10mm bolts and 2 v-slot nuts each arm (4 total for both arms) but really only needs the 2 nuts and bolts provided with the original spool holder (1 each arm). ...The threaded holder bar...

This is an adapter to be used with the original spool holder of Ender 3 V2. I have limited space above the 3D printer where the original holder is fixed. So, this thing could be used together original holder over a table. ...I'm using beside de...

I received my new Ender 3 V2, and I designed this spool holder (its a copy of CR-6 SE) I have some issues in the holes for screws. I draw 5.25mm diameter for holes, for M5 screw, but the printer make some littler. The bigger part, took me 6 hours,...

Attaches to existing spool holder allowing you to hang 2 spools as well if you wanted to, It pushes though the center of the existing spool holder. ...It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at 10%...

Attaches to existing spool holder allowing you to hang 2 spools as well if you wanted to, It pushes though the center of the existing spool holder. It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at...

This is custom spool holder I designed to accomplish the following: Low profile for my smallest and most awkward spools Use rollers rather than resting on bearings for reels that don't have a solid core, like cardboard ones Using bearings for a...

Prevent rocking as the filament slacks This spool holder is designed primarily for the ender 3 v2 as it uses the included nut plus has fitments to lock it around the arm to prevent rotation Additionally, you will need 4 608 2RS Bearings (8mm x 22mm x...

Compatible with Ender 3, Ender 3 Pro, and Ender 5 Regular Use Instructions: remove the black spool holder and bolt that came with your Ender 3. slide Filament Spool of your choice on to Pincher Spool Holder. screw Pincher Tightening Bolt onto Pincher...

In pursuit of upgrading my Ender 3, I decided to design and print a custom spool holder add-on that eliminates the need for additional parts like bearings or bolts. This innovative solution not only accommodates larger width spools but also allows...

I modified the spool holder so that i can have one filament spool in use while preparing the next filament. ... You'll need: 4 x 608 bearings 8 x M8 washers 1 x M8x180mm threaded rod 2 x M8 locking nuts Other than the 2 thing downloadable from here...

Spool Stand For Ender 3 / v2 It can only Carry 1kg or lower filaments

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

**************************************************************************************************************** This is a side-mounted spool holder with a bearing roll for the Creality Ender 3 V2. Inspired by...

Different mounting option for the spool holder.