ender 3 v2 psu fan 3d models

Bracket to mount PSU to the Ender 3 Max Remix of https://www.thingiverse.com/thing:4602648

I have an Ender 3 Pro with the rear mounted electronics box by Teaching Tech. I wanted to add a second stepper on the Z axis, but needed my power supply to be in the front. I inverted the original part and removed the wiring guide as it is no longer...

Suporte Ender 3 - V2

Remix for Ender 3 Pro PSU. Works only if you have your PSU mounted using this: https://www.thingiverse.com/thing:3898958 There is no screws, so just put it on top. ...

The 3D model in the pictures are from a Creality Ender 3 and have adapted the necessary dimensions for this project to my Creality Ender 3 pro. When removing the support, I always first pierced the edge between the support and the part with the...

Board fan guard Ender 3

a tool holder that mounts onto the PSU of the Ender 3 Pro. ...just a smaller version than the other ones on here

Just my design of a external PSU mount for Ender 3 PRO. If you used Ikea Lack or similar project this design its very helpful. ... Enjoy :)

This relocates the fat Ender 3 PSU to the back of the printer. The mount drops the PSU down to allow for a 5mm clearance between the top of the PSU to the bottom of the Y-axis stepper motor. ... WILL NEED FEET TO BE VIABLE

Here is a simple Mount for the Ender 3 Pro PSU. I used this to place the PSU outside of my Ikea Lack Case. Print twice. ...The holder provides enough clearance to keep the PSU from overheating against the wall at the backside.

This is a Meanwell 350-24 PSU stand for an Ender 3 V2. The power supply was not getting as much air as I think it should tucked away under the printer. This is a stand-alone option and I used some 200'C silicone 16 gauge wire to connect the PSU to...

Legs for the Ender 3 V2 to give clearance for the 80x80x25mm PSU Fan Swap. They will raise the printer 35mm. There are 3 sizes, with bases 55mm, 60mm and 70mm wide. The pre-existing slot fits right into the cutout. Print with TPU98A or TPU 92A...

Feet for the ender 3 v2. Gives you about 40mm of ground clearance. ...Note that the rear legs are different beacause of the psu cover

My Ender 3 came with a Mean Well PSU, similar to what I believe the Pro model uses, though my printer isn't a Pro. I liked the way the tools were held in place but found the overall design too wide for my PSU, so I decided to modify it by making it...

... is only for the Meanwell PSU from the Pro version, the older PSU is about 50mm width and will not fit! Fits all tools from Ender 3 3 tweezers 6 nozzles The holder for the clipper is the only part which needs support (my support fell over :( )

... nobble's cover to make a fanless cover for the ultimate quiet PSU. ... I've seen similar designs for other PSUs, so decided to make one for the original Ender 3 PSU. ...I have been using this for over 3 months printing non stop, and no issues so far.

The outlet and power switch on the Ender 3 Pro comes out the side and can make it difficult to fit the printer in tight spaces. ... This moves the switch and outlet to the of the psu.

All the mounting hardware that comes with the Ender 3 is designed to be installed right onto the top of the power supply unit, utilizing the screws already in place on the PSU itself.

Remixed nobble's cover to make a fanless cover for the ultimate quiet PSU.I've seen similar designs for other PSUs, so I decided to make one for the original Ender 3 PSU. ...I have been using this for over a year printing pretty often, and no issues so...

I'm modifying the Ender 3 Pro with standard Meanwell Power Supply. ... This is a straightforward revision from https://www.thingiverse.com/thing:3426861 - I shifted the screws that attach to the front and back of the PSU two millimeters to the right so...

Support for Ender 3 Creality Fans

Controller fan cover for Ender 3

A power supply mount for the original Ender 3 that keeps its stock mounting position while still allowing for adjustability and space for a dual-z stepper setup as shown in the images.This is designed for the original wide Ender 3 PSU, not slimmer...

After looking for mounting brackets to relocate my Creality Ender 3 Pro PSU so I could put my printer inside the Creality enclosure, I decided to design my own. I needed brackets to be able to relocate my PSU separately from the printer so it didn't...

I've drawn inspiration from other fanless PSU designs out there, but decided to put my own spin on it by creating one specifically tailored for the iconic Ender 3 PSU. ...After three months of non-stop printing, I'm thrilled to report that this custom...

This is a modified version of the tool caddy by SteelTallon, designed specifically to fit snugly over the Ender 3 PSU. The updated design boasts improved support for Neiko Calipers and incorporates a handy holder for a small ruler. Future...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

... on the side of the PSU. Tested with normal Ender 3 PSU, Do not know if it will work with pro or other printers, Also added a gap for some wires if need be. ...(I use it with my cpap arrangement https://www.thingiverse.com/thing:3307633) Cheers.

... as the older model is approximately 50mm in width and will not fit. + Accommodates all tools from Ender 3 + Includes 3 tweezers + Features 6 nozzles A tower has been added to deactivate supports. ...Additionally, the original mesh has been fixed.

Changes from the original include: - Top mount resized (enlarged) to fit the Mean Well LRS-350-24 PSU for the Ender 3 Pro. Note: as seen in the photo, I'm using [this PSU mod](https://www.thingiverse.com/thing:3206719) -- but it isn't required. A...