ender 3 v2 psu fan 3d models

My Ender printer lacks full support due to a reduced distance of 17mm between the power supply unit and the extruder, whereas the standard model provides 18mm of clearance for the build platform.

https://www.amazon.com/WINSINN-Blower-Upgrade-Bearing-CR-10S/dp/B08R9J189W/ref=sr_1_8?crid=2RNQRGN86YQMX&keywords=ender+3+v2+blower+fan&qid=1693871980&sprefix=ender+3+v2+blower+fan%2Caps%2C208&sr=8-8 Special Slicer Instructions: -Non CR/BL standard...

This is a revised take on mfau's carefully designed PSU cap. I've reworked the USB ports and placement to better suit my specific setup, giving me more flexibility during installation. Additionally, I've expanded the interior space to accommodate...

I needed the extra room for a buck converter but wanted to stick with a 60mm fan. ... This is a remix from JOulz original work.

... did not fit well on my power supply https://www.thingiverse.com/thing:4796284. ...The fan 8015 rested against the transformer on the board, and the side walls were not adjacent to the housing by 0.5 mm. ... Slightly modified, now it fits perfectly.

Is a Remix of Fang Fan Duct for Ender 3 V2

Power Supply cover for Ender 3 V2 to place an 80mm Noctua fan.

Compact fan duct for ender 3 V2 compatible with direct drive mods

**You need to redo some wires because the original wires are too short!** Based on the [updated version on Printables](https://www.printables.com/de/model/201359-ender-3-v2-external-electronics-box-meanwell-psu-a), I used Tinkercad - [Copy & Edit...

Link to the video where I use this case: "Adding a Noctua 60mm Fan to the Ender 3 Pro's Power Supply (PSU)" https://www.youtube.com/watch?v=C4raTp9DZa0 Link to my RC channel: https://www.youtube.com/channel/UChb38m6f-uV_DL-LkGiD3NA The LM2596s Buck...

This is a remake of Ender 3 Pro PSU Cover honeycomb 80mm fan https://www.thingiverse.com/thing:4082992 from IDDQD-. I've modified the bristles around the cover and removed the screw holes. With this, the cover becomes sturdier and fits more PSUs...

Yet another Ender 3 Pro fan cover, based on a 90mm fan and i use inserts M3 for mounting the fan internally. ...Use supports for overhanging part.

This Ender 3 PSU Silencer incorporates a handy holder for the 38mm spatula that comes with the printer. I wanted to create this because I needed both a holder and a silencer. ... The design is for Ender 3 Pro, the screw hole distance is 70.70mm.

Ender 3, Pro, & v2 will need to be raised. ... This works well with -60mm Fan Guard https://www.thingiverse.com/thing:4727329 -my riser set https://www.thingiverse.com/thing:4667594 -That was originally designed for the PSU cover...

A cover for Ender 3 pro power supply which allows using standard 120mm (or smaller) computer fan.Remix of https://www.thingiverse.com/thing:4266426Changes I've made:made it thinner (1.2mm - 4 layers @ 0.3mm) - it doesn't need to be strong and it...

A cover for Ender 3 pro power supply which allows using standard 120mm (or smaller) computer fan.Remix of https://www.thingiverse.com/thing:4266426Changes I've made:made it thinner (1.2mm - 4 layers @ 0.3mm) - it doesn't need to be strong and it...

Update V2 +V3!You can get the new version with alot of improvements on Cults.https://cults3d.com/en/3d-model/various/creality-ender-3-v2-fan-cover-ductcheers!

The stock fan that comes on the PSU of the Neptune is quite loud in my opinion so i decided to replace it with a 60mm Noctua fan.While doing this i came across a small problem: the stock fan is powerd via 24v and the noctua fan that i had bought was...

A more compact mainboard cover for Ender 3 v2, although should also fit 3 & 3 Pro. Uses the original screws in their original location. I had an 80x25 fan on hand, so your printer will need to be raised. This works well with -80mm Fan Guard -...

I added a fan for the Ender 3 V2 box by @pedrolamas My Pi 3B has heatsinks on it and since it runs 24/7 a fan is a must have. ... I run all fans as intakes

... A Raspberry Pi mount and a LM2596 mount are attached directly to the PSU wires. I also install the https://www.thingiverse.com/thing:4043475 fan silencer to eliminate wind noise from the PSU. This solution works exceptionally well. ... Enjoy!

If you don't want to do that you can take a look at my original version which can be printed on the ender 3v2.Original versionThis is an improved version of my previous Ender3 v2 electronics encloser. I've moved this so that the raspberry pi 4b...

Only for Ender 3 Pro with MeanWell LRS-350-24 power supply. Will not fit original Ender 3. This fan cover designed for faster print with 0.8 line width (using 0.4 nozzle). Total print time about 1 hour. Most of dimensions created for 0.8 line, so...

Remix to fit the Ender 3 V2 gantry plate

Remix of Ender 3 V2 & Pro Silent Motherboard by TerraVestra

This remix is for the Ender-3 V2.

Other hardware can be reused from stock Ender 3 PSU. Install sequence;Screw the mains socket into bracket without connecting the PSU. bolt down the empty bracket. Snake the 24V cable through one of the rear pass through. Lay the PSU on the build...

I printed these squash ball feet: https://www.thingiverse.com/thing:4335612 -Moved Raspberry Pi 4 down 7mm for a better fit with the original Pi PSU. -Increased size of opening for Pi PSU on side of case. ... -Added an additional fan mount for dual...

The grills of ventilos are available here: https://www.thingiverse.com/thing:2802474 _____________________________________________ Upper part of the LRS-350-24 power supply from the Ender 3 / pro. Allows you to install an 80mm x 25mm pc fan in 12v....

I changed the original file from joloman2 to have a fan guard and a base for the fan in order to screw it in the right direction without the trouble of the fins hitting the fan guard. ... I used a Noctua NF-R8 redux-1800 and i honestly cant even hear...