ender 3 v2 printed upgrades 3d models

This is a Knob for the Z-lead screw, following the design of the extruder knob found on the Ender 3 V2. I followed the diameter for the hole used by Schtimpy, which was 8 mm.. But the final outcome was a very tight fit for the Ender 3 V2. I printed...

It's a piece which matches the screw holes and slide of the ender 3 v2 perfectly Using the roller from @daGHIZmo design (I choose to print it in TPU, but PLA can be just fine) to smooth filament gliding :) Please post you're own make it you have...

This is a Knob for the Z-lead screw, following the design of the extruder knob found on the Ender 3 V2. I followed the diameter for the hole used by Schtimpy, which was 8 mm.. But the final outcome was a very tight fit for the Ender 3 V2. I printed...

Simple yet effective bl-touch mount for creality ender 3 v2 (becouse one that came with bl-touch fits only ender 3 v1). No need for additional parts, nuts or screws. ...Works perfectly with original set of screws.

There seems to be 3mm difference in the offset between the Z screw and the frame when comparing the Ender 3 Pro to the Ender 3 V2 Neo. ... Have remixed MammothMGs design to close that gap.

Made this because the x-cover from the ender 3 v2 is slightly different from the original ender 3. I personally like cows, that is why I put one on it. I also included a cover without anything. ...Enjoy!

Side 220v plug for Ender 3 V2. Designed to place the printer on a narrow table or with little space. It consists of 3 parts to avoid having to print with supports. Then it is attached with glue. No need to modify any cables. ...The original screws...

Nebula camera upgraid for my Ender 3 v2. Works well, super easy to make in SolidWorks, just print however you want, i want with 20% infill and 3 walls at 0.2 layer height. ...Shoot some comments if you want to know more.26-Feb-2024 Edit: Uploaded...

Ender 3 v2 4040 Front Switch PlateCreated in FreeCAD.Ender 3 v2, Generic PLA, 100% infill, 0.4mm nozzle, 0.2mm Layer height.I modified my Ender 3 v2 to move the power switch from the rear of the printer to the front on the end of the 40 x 40 alloy...

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. Infilll...

Screen Mount for Ender 3 V2 This one-piece print is easily printed and assembled with just an M4 nut and flatheaded bolt. it bring the screen closer to the printer. So you have the same width with or without the screen, whilst still being able to use...

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. Infilll...

... en este, se mantienen dos ductos de salida y se puede usar con el cr touch instalado. ...Print Settings Printer Brand: Creality Printer: Ender-3 V2 Neo Resolution: 0.32 Infill: 10 Filament: no pla, petg Post-Printing Category: 3D Printer Accessories

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

This is a piece for Ender 3 v2 PSU ikea lack enclosure. ...I made two pieces for easy printing Print Settings: 4 Walls 20 % infill Extra part needed: 4 head screw M3 x 8 mm PS:The prototype had to be modified (as seen in the picture), I lowered the...

This are feet designed specifically for the Ender 3 V2's blocky rectangular rubber feet. Print 4 and set your printer on top. Provides heavier dampening than your standard squishy tennis ball looking feet. ... Print with 100% infill with TPU 95A

I haven't found nut that will fit my threaded lead screw in ender 3 v2 so i designed my own. On photo is version V1. V4 should be more easy to put in. if you have PETG print in PETG! ...I printed in cheap PLA for test.

... cap, slide it on, and replace the cap. *PRINT ORIENTATION is best on it's side like shown in my 2nd pic* *PLEASE NOTE* only tested to work on my Ender 3 V2 as it has taller feet. If your Ender 3 or Ender 3 Pro are stock, this might not fit. ...

Support for the top of the Z lead screw for the Ender 3 v2 printer. Print instructionsPrinter Brand: Creality Printer: Ender 3 v2</div> Rafts: No Supports: Yes</div> Resolution: 0.16 Infill: 25%</div>

The front feet mount without issue on my Ender 3 V2, but the rear feet of 'Dr Boo's CR-10 Squash Feet' do not fit on an Ender 3 V2 due to the PSU mounting on the lower frame rails. This design allows for direct mounting of the feet using three T-nuts...

This filament guide was designed to help smoothen the flow of filament from the spool to the extruder of the Ender 3 V2 printer. The filament guide comprises of four parts. After printing the parts, they can be easily assembled by press-fitting...

This filament guide was designed to help smoothen the flow of filament from the spool to the extruder of the Ender 3 V2 printer. The filament guide comprises of four parts. After printing the parts, they can be easily assembled by press-fitting...

Ender 3 V2 Neo aluminum heat sink only.I have three Ender 3 V2 Neo heat sink (Creality parts number 3205040089) in my possession. All three have same thickness but different width and height. This model is using #1 dimensions.#1. W 41, H 34.2#2. W...

Glue stick holder ender 3 v2 take the front 2 screws out and slide it in and put your screws back in

A push on cap for the horizontal gantry of my Ender 3 V2 This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2mB6egYnj0h

Needed a way to mount my screen on the left side of my Ender 3 v2 to fit in my Creality Enclosure.

This is a kit for converting an Ender 3 V2 into a bioprinter. ... I am still working on it and will update soon.

Fixierung der hinteren Kabel für den Creality Ender 3 V2. ... Benötigt werden noch druckbare T-Nuts, M3 Muttern, M3 Schrauben Nun ist Ordnung im hinteren Bereich des Druckers.

Created this remix to fit the stock belt on the Ender 3 V2, it works but only uses two screws (as the stock mount does).