ender 3 v2 print upgrades 3d models

This is a tool/part free version of the guide by @RedSoda, it requires no nuts and bolts and you only need to print 2 parts. #### Part(s): * 1x 680(zz) bearing. #### Printing: 1. Print the `E3V2_Wheel_608zz.stl` from the original mix. 2. Print...

I saw a hexagonal stand for a prusa and wanted something similar. ...However, all the ender stands are quite boring so I made this. ...Thanks for downloading!

... the hero me gantry adapter, so i got to measuring the gantry on an EDM machine. ...so i can remix or re-draw the adapter for the v2. I heard that the v2 has multiple versions this is one of them. ...I am curious to see are there differences....

Simple box for Ender3 v2 nozzle cleaning needle. The needle is very fragile and pointy. ...The box fits in the drawer This way you can take care of the needle and your fingers.

... available for the V2. The original handle scraped against the V2's belt tightener, so I just raised the central piece up a little higher. Finger grips nicely, and its nice and tucked away under the bed. Thanks to the original creator. ...

Please take a look at [pedrolamas'](/pedrolamas) remix https://www.thingiverse.com/thing:4913020 This is part of my attempt for better cable management of the Ender3 V2 https://www.thingiverse.com/thing:4768402...

i modified this thing: https://www.thingiverse.com/thing:3589452 so it fits a bit better on the ender 3v2 on the orginal one its impossible to service the hotend and fans when it is installed

This is a nozzle holder for the parts drawer for the ender 3V2. It holds 12 nozzle's and the needle sits in the middle. ...At the top you can put the foam piece for the needle.

Cover to place fan 80x80x25 silent for ender 3v2, fits perfectly and has width space so that it does not rub with cables. this is a remake of another model in which does not fit a fan of that thickness. a current regulator is needed in case it is...

... requires a standard M4 nut (not knurled). ... Directions 1. Print Both Pieces. 2. Insert M4 Nut into Knob align with hexagon pocket.. 3. Place Cap on knob. ... When I put this together, I didn't require any glue and the cap was very secure.

... the print head. I used some cheap COB LED chips from dollar store flashlights and wired them up in parallel for use with any phone charger or any DC 5 volt power supply. I put holes for wires to pass through and 3 holes on the top for 3 zip ties.

Small HSW module with attachment for Ender rails. I've put mine on top of the printer and holds bits and bobs nicely. ...And looks cool while doing so.Check out HSW here:https://www.printables.com/model/152592-honeycomb-storage-wall

This part has 3 goals: Contain the extruder led switch Hide cables Cable chains support It must be printed with the switches face down. This piece was designed to avoid the use of supports as much as possible. The only place where support will be...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. This is a redesigned version of my other bracket. I incorporated more support on the "shelf" itself...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. This is a redesigned version of my other bracket. I incorporated more support on the "shelf"...

The hole for the axle is designed at 8mm, but usually ends up smaller in printing so I make the Axle 7.5mm in diameter. (Mine is loose but it spins freely so that works for me). There are 3 spacers, 2 on either side of the wheel (spacers), and one...

The knob is attached to the cover with one 4 x 3/8 screw

Takes less time to print Then OG

Easy to print gear without the need for distribution after printing

Simple print badge for the E3V2 printer. ... Can be glued anywhere after printing

Cam holder Cam 50mm PLA Nozzle 0.4mm Hight 0.2mm Bottom Layers 4 Top Layers 4 Walls 3

Cam Holder Cam 50mm PLA Nozzle 0.4mm Hight 0.2mm Bottom Layers 4 Top Layers 4 Walls 3

Dragon logo 0.2mm nozzle used while printing

My version of a very simple spool holder without use of ball bearings.Dimension : 5.3 cm x 4.4 cm x 4.0 cm

Designed this one for my printer to cover the screen when i'm printing at night

Brought to you to avoid a bright screen during those late night prints.

Modified the original design to accept a normal webcam. ...Print as described as in the original post.

Print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking mesh.

... side made a angle to dodge the bed and made a swivel loop to move with the printer. ...Print both standing up. When you print something high it will pull the ring out of the base it does not damage anything simply put it back after you print is done

Utilizes the extruder feed spring tension screw. ... Easy print to keep wires neat. ... Screw hole is an interference fit to keep the mount from wiggling.