ender 3 v2 part cooling fan 3d models

Ender 3 Pro super silent mod:   2in1 hotend-part cooling for 80mm silent fan ( for best result: change mainboard fan and power supply fan into 80 mm silent fan )    

a very basic part cooler for an ender 3 with a 5015 fan. ...

TIP ---- To achieve optimal results, position the BL touch so that its logo is facing inward and the internal PCB is positioned furthest away from the fan. A loop has been added for securing the wires of the bl-touch using cable ties. ... For printing...

For example:https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offsethttps://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...

I replaced my Ender 3 part cooling fan with a 5015 blower and measured the original with the new and it was a perfect match. So I thought well let's see what we can put together. I'm not good at 3d modeling but I can work a little with Tinkercad....

Remix from wheelwrench adding a guard below the part cooling fan and beefing up the top layer that touches the silicon cover. ... Printed at 200c with build plate temp of 60c with my Modded Ender 3 Pro.

... groove mount. WARNING: The filament/part cooling fan blows air 3mm below the base. If your nozzle protrudes more than 3mm from the base, it will cool your nozzle instead! ...This design works great with standard flathead E3D nozzles or MK8 nozzles.

Use part 1 and 3 from the original. ...This part 2 has the holes used in the Ender 3 v2 power switch and plug.

I wired the three 5015 fans in parallel with the part cooling fan so they turn on and run at the same percentage as the part cooling fan. ... These are the blower fans it was designed around:...

The FT-5 is upgraded with a cooling fan mount and full ring claw designed specifically for use with the ultralight carriage from 713maker, BondTech BMG extruder and E3D V6 hotend. ... This update now includes a claw plate for the E3D Volcano that lowers...

Upgrades on my Ender 3 V2: === My 3D Printer Ender 3 V2 Silicone dampers Creality CR Touch Auto Leveling Micro Swiss Dual Gear Extruder Micro Swiss all Metal Hotend Filament I have printed the spare part: === eSun ePLA-ST Black Visit also our...

I recently purchased the Ender 3 printer and began tinkering before fully assembling the entire unit, finding it to be quite amusing. The Fan Duct Ring fits perfectly in place with a deliberate gap on both the extruder side and nozzle tip side; I'm...

---------------------------------------- Bobblejot Website Bobblejot GitHub Bobblejot Twitter Bobblejot Patreon ---------------------------------------- New part fan shroud based on the Tusk concept for the Creality Ender 3 or compatible printers...

---------------------------------------- [Bobblejot Website](http://bobblejot.com) [Bobblejot GitHub](https://github.com/Bobblejot/) [Bobblejot Twitter](https://twitter.com/bobblejot) New part fan shroud based on the Tusk concept for Creality Ender...

The hinged design of side fans is a game-changer, allowing for unparalleled ventilation. Airflow gets a boost, making this mount even more effective. ... **Print Settings:** * Printer Brand: RepRap * Printer Model: Kossel * Rafts: Not Required *...

This particular model incorporates a single-part cooling fan - an identical dual-fan variant is also available. The absence of PTFE in the hotend design enables extremely high print temperatures and significantly reduces the likelihood of...

This is a part of a cooling fan, made by me.

Antonio Guardia designed this part cooling fan project specifically for the AGraber 30i.

I wanted a superior part cooling fan shroud that could seamlessly replace the factory one. It was my first print and I'm thoroughly pleased with the outcome. Eventually, I plan on printing the Petsfang, but this will keep me satisfied for now. This...

This is a simple replacement part for the Ender 3 V2 (V1?). There is a small difference in comparison to the original part. The "knob" is a little longer, so that the nozzle is higher above the hotbed. The reason is that my springs for the hotbed...

The Ender 3 S1 Pro definitely needs more part cooling, especially if you want to print at higher speeds. I searched to see if anyone has already solved this problem. Thanks to all of the work from Stuart800 and Merkaba to get me started. Let me...

There are slight improvements on the bottom of the split in the Y and X.I'm planning a V2 to reduce the footprint of the duct as well as another Noctua cooling solution to cool the heatsink ( its very tricky/impossible with an axial flow fan)A note...

I'm planning a V2 to reduce the footprint of the duct as well as another Noctua cooling solution to cool the heatsink ( its very tricky/impossible with an axial flow fan) A note to anyone designing 40mm Noctua cooling ducts for any and all printers...

=============================================================== Introducing a Fresh Take on the Part Fan Cooler Duct This innovative duct is specifically designed to elevate ABS/PLA printing. It boasts three key functions that work in harmony to...

fan cover magnetic Ender 3 V2

Im currently designing my own printer from scratch mainly for speed but on the cheep, so took the idea using an Ender 3 but made for pure speed hence the name "Bed Slinger" trying to keep the hotend lightweight as possible i made this part cooling...

I haven't found nut that will fit my threaded lead screw in ender 3 v2 so i designed my own. On photo is version V1. V4 should be more easy to put in. if you have PETG print in PETG! ...I printed in cheap PLA for test.

This is for NF-Crazy+ Hotend which the screw holes are compatible with CR-10 & Ender 3 X Carriage. ... You can use the BLTouch bracket & BMG Bracket on this design: https://www.thingiverse.com/thing:3466809 You will need an M3 insert screw to fix the...

... it. ... Gives a much better view on the nozzle and doesnt sucks in the hot air from heat bed and maby also better cooling Fits nicely WINSINN 4010 fans I printed it out of Polymax PC and didnt had any problems with melting parts under hard conditions.

I modified my Climber7 part cooling fan using "Plasticene" and noticed an improvement using PETG, so I'd thought I'd set about making a STL model to refine the idea. There are some volume constraints with this part within the hot end enclosure, so I...