ender 3 v2 part cooling fan 3d models

I also added spacers/standoffs that should help avoid an issue I was having, where I needed to use longer screws to mount the board, due to the soldering points on the back of my SKR Mini E3 V2. (It probably works fine with the original design, as...

I also added spacers/standoffs that should help avoid an issue I was having, where I needed to use longer screws to mount the board, due to the soldering points on the back of my SKR Mini E3 V2. (It probably works fine with the original design, as...

For users upgrading the part-cooling fans, this allows for a lightweight solution than the very large 'cages' that go around the hotend to hold a 4010 fan. Example image shown using the KLEMCO groove mount adapter and ducts that can be found here...

These are the print parts of the F3 Innovator All Metal Hotend, designed specifically for the Ender 3 printer. You can find it on f3-innovator.de and use it on CR-10 and Tronxy X5S models as well. This hotend is capable of printing all types of...

I did this in conjunction with upgrading the mainboard and psu fans to noctuas as well (https://www.thingiverse.com/make:903901) Fan: https://www.amazon.com/Noctua-NF-A4x20-PWM-Premium-Quality-Quiet/dp/B071W93333 Buck Converter:...

Este es un remix de Este modelo https://www.printables.com/model/430053-franzoli-direct-drive-ender-3-pro/comments Me encanto cuando lo vi, pero he tenido el problema de que el extrusor no encajaba, quedaba muy arriba, no se si lo hice mal yo o no es...

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

... Due to the extra height feet risers are required. I used these https://www.thingiverse.com/thing:4603075. There is not enough clearance between the right rear foot and fan cover so I include modified foot to compensate for that. 

Pure Wings 2 fan, but should work with other 120mm fans as well. Overkill for sure, but I already had these fans on hand from an old PC build. Remixed Terminal cover as well. https://www.thingiverse.com/thing:4774312 note. Due to the extra...

I designed a simple enclosure for the Noctua 40x20 fan to use on my Ender 3 printer, incorporating a BL-Touch mount from Thingiverse (https://www.thingiverse.com/thing:2493610). Everything prints out as one piece. I printed it with 100% infill,...

Micro swiss direct drive extruder fan holder for ender 3, ender 3 pro and ender 3 v2 with x-axis correction. This is two part body (part no. 1 and part no. 2), after printing two body must stick together with plastic adhesive glue. This is because...

... 2) Wired the Fan to the buck converter. 3) Pre-wire you buck converter 4) Clip the buck converter in place 5) Screw the Fan with the supplied screws 6) Be sure your printer is turned OFF and wired the buck converter to mainboard supply. ...

40x10 Blower Fan 40x10 Fan E3DV5 Hotend

I will upload a V2 soon) —- This is a remix from the 80x25 version to fit a 92mm fan. This cover houses a 92x25mm fan and you can fix a LM2596 buck converter but this is not mandatory for the PSU fan. You will need 2 extra M3x6 screws to fix the...

Enthaltene STL-Datein: 60mm_PSU_Cover 80mm_PSU_Cover 60mm_FAN_Cover 60mm_FAN_Cover_with_GRID 80mm_FAN_Cover 80mm_FAN_Cover_with_GRID TOP_Cover_CABLE Hinweis: Ich habe die 80mm Version nicht getestet! Sollte das nicht passen würde ich mich über eine...

With this one, all you need to do is remove one M3 screw that holds the Fan Shroud to the Backing Plate (BL Touch plate) I recommend Printing all parts on their back and using tree supports for printing. Again, I hope you enjoy! If you decide to...

Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.comThis is a remix of Victor Bared's remix, in his silent fan mod upgrade videohttps://www.youtube.com/watch?v=ycvHpMbo5HwHe split the PSU cover into 3 pieces to...

Satsana Fanduct with support for 2 part cooling fans

Standoffs now have a ID of 4.8 mm, OD 6.3 mm and height of 3.75 mm. These values are parametric and can be adjusted. I am fairly new to modeling and have no experience sharing parametric files and very little with editing existing files. ...Let me...

Redesigned for use with Sunon fan 80x80x15mm

... for the Creality spider hotend as its longer then the stock hot end. ... You must use the slimmer boden connection that comes with the spider the wider one that is installed by default is to wide Download all the rest of the part's from the Original

Anything hotter may warp the Part Fan. I designed this in hopes that some people will be able to make custom fan ducts for a design that has a dedicated place for BL touch. I got sick of removing my Satsana Fan shroud whenever I needed to do...

You'll be able to mount a 80x80x24 Fan with a buck converter in this cover.Material required:1x Buck converter --> https://www.aliexpress.com/item/32912622343.html1x 80x80 Fan --> Your choiceAssembly instructions.1) Adjust the voltage of your...

Here is a support for the ADKS duct fan to mount a BLtouch, compatible with the ENDER3 and ENDER 3 V2. It is adjustable in height. ... Thanks to the creator of ADKS - Ender 3 Fan Duct v3 for the work done.

Modified the air ducts to be more centered around the nozzle and tapered the part that goes into the fan. The hot end no longer needs to be removed to install the locking tab. Since the locking tab is now flat on the bottom, it's easier to print...

Bought the wrong size fan so edit the fan mount and increased the vents for better ventilation:)

Remix of an existing naked fan mount with a couple tweaks to improve fit. ...Press fit to put the fan into the fan and press fit to add the mount to the hot end, no tools required.

Improved Tevoup Hydra part cooling fan duct to fix the cooling issue

Modified the Fan Ducts to give the extra reach needed for the Creality spider hotend as its longer then the stock hot end.You must use the slimmer boden connection that comes with the spider the wider one that is installed by default is to...

CR Touch mount for this particular remix of the Satsana Fan Duct