ender 3 v2 part cooling fan 3d models

Found amazing Ender 3 fan cover remixed by [myeh2k](https://www.thingiverse.com/myeh2k) and decided to make it more cthulhu like. Center symbol is sigil of the gateway. Symbols on right and left are just cthulhu fhtagn written in lovecraftian font. ...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

The original fan shroud was leaking around the bottom and cooling the heater block causing thermal runaway on the stock hotend. I modified the shroud to better cover the heater block and greatly reduced leakage. ...This shroud was added to a dual 5015...

Simple full power supply cover replacement to install silent fan on the Meanwell PSU of the Creality Ender 3v2. This design is for 80x80x10 fan, in my case i used this one :...

With this booster I got roughly extra 2-3 m/s of air speed at the heatsink end of the duct with a Sunon MF40202VX-1000U-A99 fan (measured with an anemometer) - duct_heatsink_compressor_brace.STL -> integrates the static pressure booster and the...

Remix of mplantain's original file w/ ender logo

This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...

null Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

I remixed the LH top cover for a 92mm Noctua fan https://a.co/d/7cM5Tpj

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy

This is my creation of a Y axis fan mount. ...I recently did a 24hr print and I noticed the y axis motor was kinda warm. It is designed to accept a 4010 size fan, preferably a 2 wire 24V.

Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.

(in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596...

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

... you have fan on psu this is possible you should reverse this on your Slicer. Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www .thingiverse.com/thing:4707243 Because i using a two the same fan.

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

Just a redesign to fit a 8025 fan to the psu. Needs these legs to work. ... https://www.thingiverse.com/thing:4603075

... of the 14, so instead of re-ordering I thought I would adjust this cover so it will fit. ... I did use the original cover as a stop gap by cutting away the fan shroud on the top and press fitting it through as I had already soldered in the new fan.

I made a little clip to hold the fan shroud in place. ...I hated turning the printer around every time I wanted to change the nozzle or get inside the fan shroud. ...I took out the screws on the back of the plate, and use this clip instead.

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

I designed the original, but the long-term use was not reliable, so I designed it a little more. ...I added a curved front to accommodate the shape of the fan shroud, and a longer tab underneath

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

Micro Swiss hotend with two 40mm fans, never again disassemble everything - the hotend cooler is installed and the nozzle cooler screwed in. ...Now you can access everywhere easily during a fault search.

Changes I did: - Added enouth depth for the fan to fit inside (you will need more filament) - Cover all the holes except the fan one. Don't forget, print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking...

Lay this flat, no support, modified satsana for direct drive clearance. ... I'll upload the direct drive file soon, needs tweaking still I cut out a lot, and tons of space by the nozzle for a LED. Its like a satsana mini but dual fan.

I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...