ender 3 v2 octopi 3d models

I didn't like any of the solutions I found for mounting an OctoPi on an Ender 3-V2, so I spent a preposterous amount of time creating one. I don't think the storage drawer is very useful, so I designed it to use that space, and to also house a couple...

This is a Camera Arm for the Ender 3 v2 Printer. I am pretty sure it works on other printers, but if it doesn't, lmk in comments, and I will make a version for them! Have a great day! ... copyright Ben Walker

I've colour matched my LED to the one that's included in the Ender 3 V2 Neo CR touch to make it extra snazzy, Just screw mount the Raspberry Pi to the drawer base. I used recessed M2.5 screws that screw into a heat-sink from the bottom up. Then it's...

The tool-drawer holder in the Ender 3 v2 is the perfect place to put a Raspberry Pi running OctoPrint’s OctoPi (big shout outs to Gina Häußge and Guy Sheffer). Just screw the RasPi on the frame, plug in the connectors and slide it into the printer....

English A case for the Raspberry Pi to get the most out of Octoprint, with short cable runs this case adapts perfectly to the Ender 3 v2, as if it was already designed that way at purchase. </p> <p>The 24V power supply line can be laid directly in...

This is an easy-to-print storage tray for an Octopi - tested to fit a Raspberry Pi Model 3b. ...No support should be necessary printing from the face down.

This is a Remix of the [Ender 3 v2 Hidden OctoPi Mount](https://www.thingiverse.com/thing:5201485), by [Department_Nine](https://www.thingiverse.com/department_nine/designs). For more varity have a look at the Original. ... I Realy liked the Original...

Remix from https://www.thingiverse.com/thing:4648289. I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders...

Printer (for drawer size): Ender 3 V2 Neo Fan: 30mm that I'm pretty sure came with a canakit years ago. Should be standard. Pi: 3B+, though it should fit 2, 3, and 4. Relay: [AZKO 5v Relay Board Relay...

Adafruit Raspberry Pi Zero Case with added mounting rods to support mounting to the side of the Ender 3 v2. Snaps into place nicely with a little bit of force. Some people have reported issues fitting the Raspberry Pi Zero Wireless version into...

removed the need for the lid hole add in a hole for the pi cam as is a tight fit and i will be using the pi cam also add in rails for the base as found the bars loose these will slide in and fit for my ender 3

... but old case would make it very close to the lid based on the stock heatsink you can buy, for the lid i made some holes where the heatsink should be so it can vent. ...Also changed bottom to a rail base that is very tight but fits my ender 3 perfectly

This is a case I designed, and a base mount i redesigned to work with my Raspberry Pi 3b+, Ender 3 V2 and a 3.5" OSOYOO touchscreen: https://www.amazon.com/gp/product/B08634Y16L/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 -Print the Base and...

This is a case I designed, and a base mount i redesigned to work with my Raspberry Pi 3b+, Ender 3 V2 and a 3.5" OSOYOO touchscreen: https://www.amazon.com/gp/product/B08634Y16L/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&amp;psc=1 -Print the Base and...

SKR V2/Ender 3, Neopixels (huge pain) ,Octopi, Relay controlled power for both printer and LEDs via Octoprint interface USB power disabled on raspberry pi instructions/ the 5V led version Raspberry pi v3 Everything else you need is in the power-point...

I remade a octopi mount to inculde a screen where you can put some information from te raspberry pi. With this versin you need to use a full size raspbery pi, 40mm fan (10mm thick) and a SSD1306 OLED screen. - link for the fan i used:...

I can across a Ender 3 V2 screen case FredrikA had designed, and decided I could extend it to also include my phone - It would be 'double screen'. I extended the mount, and made it longer and stronger to accommodate the extra width and extended...

I have combined the two designs into one, to make this case for you raspberry pi 4. In this case you can fit a raspberry pi 4 and a 0.96 inch oled screen (links down below). This design is compatible with a 40 mm and 30 mm fan for cooling. ...I have...

remix of https://www.thingiverse.com/thing:3294512 and https://www.thingiverse.com/thing:1415895 to fit the Ender 3 v2 with a raspberry pi 3 B+ and camera for octoPi

#Summary Mount your Raspberry Pi 4 under your Ender 3 Max Dispay #Designed For - Ender 3 Max (Will not work with other Ender 3 models) - Rapsberry Pi 4 (Will not work with other Raspberry Pi models) #Sources https://www.thingiverse.com/thing:3700643...

Great for an OctoPi setup!  You will have to use a very small amount of hot glue on the corners for the frame portion of this print, to attach it to the housing of your display. ... The cover portion fits nicely within the frame and can be removed...

... was perfectly suited, but I wanted to make some slight adjustments to include a bracket that securely attaches to a 2020 extrusion. This modification allows for seamless integration on the Ender 3, positioning it neatly below the display panel.

Parts: 1 - Raspberry Pi 4 1 - 30x30mm Fan (comes with many pi heat sync kits) 1 - 30A Single Channel Relay 1 or 2 - Buck Converters (One for the Pi and One for all NeoPixels as their draw will put a pi into low power errors if they share) 3 - Female...

When I switch to an SKR 1.3, this won't be an issue. As such, I basically mirrored the box. Obviously, leaving the RasPi cutouts in the same orientation. My only issue is that the cable for the Pi camera now has to go over or under the whole board to...

This is a basic octopi station that goes under your display module and can store your raspberry pi (either model 3 or 4)

An Ender 3 Max remix of the Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure by eoyilmaz. A modified version for the Ender 3 Max using Tinkercad. Fits great, add a fan on top of the pi for extra cooling. Note: Drill an angled hole for...

I was looking for a way to get my printer more organized and decided that I would mount the Raspberry Pi Eviciv touchscreen I use for OctoPi on the Ender top bar. The top bar is 20mm and this mount has a few features to make it easy to remove. ...

Here is rewritten text: The Ender 3 Pro 2 release is paired with a Raspberry Pi 3B model, while the DC-to-DC power supply uses an LM2596 module. ...The relay is provided by HiLetgo.

These are two models that I reworked for the Ender 3 Max and added a spot for a 4010 fan for active cooling. ... The BTT is reworked for a BBT E3 V3 screen and a Pi4

... getting really hot in there. ### Top Version 2.0 Top of the case has a hole for a cooling fan. Now it's much better. ### Top Version 3.0 Added a fan cover, so the parts get cool air for cooling instead of the hot air under the heatbet. ...