ender 3 v2 neo 3d models

... en este, se mantienen dos ductos de salida y se puede usar con el cr touch instalado. ...Print Settings Printer Brand: Creality Printer: Ender-3 V2 Neo Resolution: 0.32 Infill: 10 Filament: no pla, petg Post-Printing Category: 3D Printer Accessories

This holder fits the Ender 3 V2 Neo

Minimal holder for SD card adapter on Ender 3 V2 Neo.

This is a slightly modified version of the Light mount for an Ender 3 V2 Neo.

... to the post. I'm pretty new to designing parts.) V2 Neo Shroud: https://www.thingiverse.com/thing:5610691 Ender 3 Shroud: https://thangs.com/designer/CyJax/3d-model/Stock%20Fan%20Shroud%20Replacement%20for%20Better%20Visibility%20and%20Cooling-23504

Ender 3 v2 led top and side led bar The installation was made with a 1 meter led 5050 strip

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

This holder fits the V2 Neo which comes with a stubbier small wrench (10.5mm handle), which will now fit. This holder should work really on any Ender machine and non other brands that have the same/similar rail. ... Note: For best finish print like in...

This is a direct replacement hotend cover for the Ender V2 Neo. It works with the standard fans only. It lines up with the blower fan intake better than the original. I added 4 LED's to the eyes and below to light up the print area. I use 2k ohm...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

... ...I used original reel mount hardware to attach it to overhead gantry. I screwed the two pieces together for horizontal stability. the screw hole is 3.5mm. ...You can position the assembly wherever you like on the gantry to suit your needs.

Remixed Tomaskom_cz's design to work with my Ender 3 V2 Neo. ...Slides into the top rail and is a little longer than the original design.

Remix of https://www.thingiverse.com/thing:5448871 The Ender 3 V2 Neo has a closed frame at the front, so I only adjusted the fit.

... endcap made of plastic on the Ender 3 V2 Neo. ...Mine cracked and it doesn't seem like you can buy a replacement online, so here we are. Print settings on the Ender 3 V2 Neo:Filament: PLASpeed: 50mm/s wall, 75mm/s infillInfill: 15%Temperature: 205C

The (very) crude modifications I made to Beh01der's design include a notch on one of the clips to clear a mounting clip from the shroud, repositioning a cutout to clear a screw head and reducing the distance between the 2 ends of the clip to match...

Modified the design by marc023 so that it works with the ender 3 v2 neo without screws v2: holds in place perfectly v1: doesn't actually hold in place, just a test peace to see if it fits

couldnt find this so i created it. ...this is the x axis cover for the belt tensioner on the Ender 3 V2 NEO (only!)Printed at0.16mmPLAScrew mount side up on plater

I use this to help me reattach my Magnetic bed Onto my ender 3 v2 neo. ...I slide it on the Corner then place the bed over it aligning it and then remove it before Printing again

Remixed LED lighting for my Ender 3 V2 Neo printer. You can use your ring youtuber led lighting by adding a camera screw. ... Original Sources; https://www.thingiverse.com/thing:2749041 https://www.thingiverse.com/thing:2973859