ender 3 v2 neo upgrades 3d models
822140 3d models found related to ender 3 v2 neo upgrades.
prusaprinters
Many thanks!https://www.paypal.com/paypalme/mrhuy01081999 How I Designed This Autodesk Fusion 360 Print SettingsPrinter Brand:CrealityPrinter:Ender 3 V2Rafts:NoSupports:YesResolution:0.2mmInfill:40%Filament:ESUN PLA +Color:Suit...
prusaprinters
The cost for this upgrade is approximately €40.Printed parts, inserts and screws.X-AxisLeft X Shaft Holder: 2x Short M3 inserts, 2x M3x5 setscrews.Right X Shaft Holder: 2x Short M3 inserts, 2x M3x5 setscrews, 1x M4x10 socketscrews, 1x M4 T-slot...
thingiverse
This is a bracket for use when upgrading a Creality Ender 3 V2 Neo with a Titan direct drive kit. ...The bracket will attach to the two offset holes on the x axis motion assembly and will hold the CR-Touch device as well as the accelerometer that comes...
thingiverse
Fixed the filament guide that Mosaic put out to actually line up with the filament feed of the ender 3. ... Needs scaled to 254% due to my messing up the scale in the fusion 360 export.
thingiverse
This upgrade/mod adds a light bar to your printer
cults3d
Bracket for perpendicular repositioning of the filament holder on Ender 3 / Ender 3 V2 printers. With the present mod the filament holder is located parallel to the hot bed. ... The present mod is very useful for direct extrusion modified printers.
thingiverse
made for use with bearing ZNL 1000806 2RS 61806 6806 and ESUN filament coil fix some problems with filament stuck replace default filament holder from ender 3 v2 neo, use default nut
thingiverse
Creality Ender 3 V2 Neo. ... Assembly hardware: 4X - Stock M3 filament sensor screws 4X - M3 nuts 1X - Stock Nyloc nut from top X motor/wheel mount bracket Top and bottom layers .8 Walls .8
thingiverse
The original house was a little small for the mBot I got, turns out mine is the v2 (mBot2 Neo), so I made this remix following my kid's requirements for a house.
prusaprinters
Found an Oreo or Benchy knob you want to use on your Ender 3 or Ender 3 Pro but it's made for an Ender 3 V2? Look no further than this simple adapter piece. This adapter can be super glued into place, I personally didn't have any on hand so I just...
cults3d
Ender-3 V2 belt tensioners system for the Ender-3 Pro. I liked the original design (https://www.thingiverse.com/thing:4942809), but I had to rework it to make it easy to use. ... Additional mounting materials: * 2x M5x30mm hex screw * 2x M4x20mm...
thingiverse
A remix with an added sd/microsd/usba slots.
thingiverse
This is a remix of a Remix, original here https://www.thingiverse.com/thing:5927471 Since I couldn't find a 5015 blower in my zone I had to modify the shroud to use a 4020 one. It works like a charm! No more problems with cooling! First I...
thingiverse
An adjustable version of sadrummer06's end stop switch cap.
thingiverse
filament guide Can be screwed directly under the original RunOutSensor, with the screws of the sensor or with M3x30. Models: -Bracket -Ball bearing adapter x2 -Leadership -bolt screwless ;) Filament Führung Kann direkt unter den...
thingiverse
This small piece is a thinner replacement for the spacer between the bolt and the extruder handle. The bolt was sitting barely in the thread, causing me to damage the thread by tightening that specific bolt. As a result, I've designed a new spacer...
thingiverse
Turn your Ender 3 Pro into an Ender 3 V2 ising the Ender 3 Pro's LCD mount. The only prerequisit is that the Ender 3 Pro needs to have a Crealily 32bit board (either v4.2.2 or v4.2.7) and install the appropriate firmware. I strongly recommend Jyers...