ender 3 v2 neo upgrades 3d models

All measurements were made by me on the heatsink I received as part of the Ender 3 Neo kit. Some of the hole locations and some of the dimensions are different from other models I found online. ...For example, the heater mounting holes are centrally...

This is a remix of Ender 3 Pro Direct Drive Harness Holder to Fit on the Neo extruder mount that is about 8mm bigger in width.I used PETG but should work fine with PLA.Print with supports, you'll need a sharp blade to remove the supports from the...

Ender 3 cover

Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...

It is a filament guide for the Ender 3 Neo (v1) that snaps right into place. It sticks out to the left of the printer by about 10cm, guiding the filament nicely in an arc instead of it going straight down. ... Sliced with Cura - Note: Support...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

This is a mount for a Raspberry Pi to an Ender 3 NEO in a case. You need to create 2 of these to hold the Raspberry Pi. I added M4 screw holes, but so far haven't needed to use the screws. I also included the scad files to customize it to your...

I couldn’t find anything to my liking that fit the Ender 3 Neo 3D due to the wider stock hotend. I used the the stock screws for the hotend and one of the blower fan screws to hold this in place. M3 screws and heat-in inserts to hold the fans in...

I took his overall design and ideas from other filament guides specifically for the Ender 3 models and made a model for the Ender 3 Max Neo. For my final design, is designed it to mount directly under the extruder on the Ender 3 Max Neo. The...

Modified for ENDER 3 MAX NEO printer and outer 4mm PTFE tube. Printed with a 06 noddle, for this piece, in my case, I prioritized printing speed more than quality. It will come out with better quality if it is printed with a 04 nozzle and 0,16...

Complete replacement to the Ender 3 Max Neo tool drawer to hold a Raspberry Pi 3, Buck Converter and Relay. Design of the tool drawer should work for Ender 3 v2 as well. The design is intended to use the original "case" for the tool drawer but...

Remixed from: https://www.printables.com/cs/model/115518-biqu-h2-ender-3-v2-mounting-plate-with-bltouch Intended to be used with: https://www.printables.com/model/114869-biqu-h2-extruder-part-cooling-duct-mount and...

Model description: Housing for LED strip for Ender 3 NEO printer.I used an 8.1 mm wide LED strip, 6.2 mm wide LEDs. I bought it here. Description of bodies:  Body1 - are two slats that are glued (optional) together at the bottom.  Body2 - is a cover...

This is for an Ender 3 Neo with the extender 400 ender 3 pro kit . you will also need feet on the printer, I got mine here https://www.thingiverse.com/thing:5522084 . This is designed to house the 4.2.2 mainboard and a 120mm thin fan . I am hoping I...

... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...

tool holder for the tools supplied with the ender 3 + a cutome case

My cover break apart after many times disassembly so I remix this replacement part. ... Original design: https://www.printables.com/model/377901-ender-3-s1-x-motor-cover Print like image to save time & have better tolerance.

There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...

This bracket mounts the factory spool holder from the Max Neo to the top rail. You can use the same screw that comes with the original holder. This is a quick prototype that still needs a little work, but I could not find anything similar. ... I...

Additional parts needed 2@ M4 X 16 screws 2 @ M4 T Slot Nut Fastener This is a top gantry LED mount for an END 3 Max Neo. It pairs with my X Axis gantry LED mount. https://www.thingiverse.com/thing:5931926. This design is good to give overall...

It's a slightly redesigned air duct that features elongated mounting pad for 3 strips of 10mm LED tape - https://pl.aliexpress.com/item/1005001681576572.html?spm=a2g0o.order_list.order_list_main.20.36561c24wW8A3o&gatewayAdapt=glo2polthis tape in my...

BMG feeder bracket with adapter for stock head. (provides a rigid mount). I have a custom case, but in theory it should fit into a completely stock head. Supports required only for connector PET-G is fine. I'm waiting for feedback, I can correct...

Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.com

Annoyed that the design did not take into account the silicone sock. Something I threw together very swiftly and printed to verify. I printed with a .6 nozzle out of PETG and seems to be clearanced enough to not get melted on the sock. ...

Suporte Ender 3 - V2

ENDER 3 PRO UPGRADE HOTEND

This is a collection of my "heavly remixed" upgrades for ender 3 pro. I really liked the idea behind the cable chain maded by NG_Designs ; https://www.thingiverse.com/thing:3769941 but i decided to redesign it because it's really hard and long to...

Clean display cover upgrade for Creatility Ender 3 v2. ... Added screw holes and removed watermark from bottom lip.

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...