ender 3 v2 neo thermistor 3d models

I published a beta version of the print head model of the Ender 3 Neo 3D printer. ...I will supplement it with new elements as reverse engineering progresses.

I can't find the model I used as a base but it needed some adjustments to fit on the ender 3 neo max.Enjoy!

An LED bar for LEDs with a width of 8mm.The length is adjusted to 420mm to fill / illuminate the entire width of the Ender 3 Max Neo.

... I can think to make it. This is "Version 1", so it may not be 100% accurate. I really just modeled it so I could design some custom fan shrouds and such. This may also work for the Ender 3 V2 Neo as well? I'm not sure. ...Do with it what you will.

This piece is for the Ender 3 Max Neo. It allows for filament to be top-mounted on the printer. It uses a standard skateboard bearing for the wheel. I need to add a few parts later for the bearing. ...

Warning. ...All measurements were taken by me on the heater that I received as part of the Ender 3 Neo kit. ...Some hole locations and some dimensions are different from other models I found online.

... 5015 blower fan. I also have a Noctua 4020 fan but it is compatible with the fan that comes with the Ender 3 Neo. ... To be honest, you shouldn't upgrade to the Noctua fan because any noise reduction due to this fan is drowned out by the 5015 fan.

LED mount for Ender 3 Max Neo, should work fine for any Neo/V2 Ender Printers. I wanted an LED mount that would light the print as the Z axis raised. I tried a couple different mounts and this one worked best for me. One of my designed the LEDs...

I will update it as soon as i take measurements. This is a model set of three parts from 3 separate individual creators that I've put together in order for ender 3 neo users to create more varieties of adapters, shrouds, fan casings etc. I'm super...

Because of the CRTouch Senser added to Ender 3 Neo, many solutions attached to this position no longer works for my 3D printer, and I modified it a bit to ensure the C270 camera can be mounted without destructive modification. ...The image is a...

... can be removed for maintenance. Uses a single standard screw into the back to affix to the frame, but clips should work fine. Mine is installed on the Ender 3 Max NEO, but should work on any of the Creality NEO printers. ...Designed with Fusion 360.

All measurements were made by me on the heatsink I received as part of the Ender 3 Neo kit. Some of the hole locations and some of the dimensions are different from other models I found online. ...For example, the heater mounting holes are centrally...

This is a remix of Ender 3 Pro Direct Drive Harness Holder to Fit on the Neo extruder mount that is about 8mm bigger in width.I used PETG but should work fine with PLA.Print with supports, you'll need a sharp blade to remove the supports from the...

Крепеж экструдера BIQU H2 V2S на Ender 3 NEO под хитблок VOLCANO!Для крепления к каретке используются 2 винта М3х8 из комплекта BiquСам Biqu прикручивается слева на один М3 из комплекта, сверху-снизу на два М3х4 от родного экструдера E3NEOЯ печатал...

Ender 3 cover

Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...

This is a mount for a Raspberry Pi to an Ender 3 NEO in a case. You need to create 2 of these to hold the Raspberry Pi. I added M4 screw holes, but so far haven't needed to use the screws. I also included the scad files to customize it to your...

It is a filament guide for the Ender 3 Neo (v1) that snaps right into place. It sticks out to the left of the printer by about 10cm, guiding the filament nicely in an arc instead of it going straight down. ... Sliced with Cura - Note: Support...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

I couldn’t find anything to my liking that fit the Ender 3 Neo 3D due to the wider stock hotend. I used the the stock screws for the hotend and one of the blower fan screws to hold this in place. M3 screws and heat-in inserts to hold the fans in...

I took his overall design and ideas from other filament guides specifically for the Ender 3 models and made a model for the Ender 3 Max Neo. For my final design, is designed it to mount directly under the extruder on the Ender 3 Max Neo. The...

Modified for ENDER 3 MAX NEO printer and outer 4mm PTFE tube. Printed with a 06 noddle, for this piece, in my case, I prioritized printing speed more than quality. It will come out with better quality if it is printed with a 04 nozzle and 0,16...

Complete replacement to the Ender 3 Max Neo tool drawer to hold a Raspberry Pi 3, Buck Converter and Relay. Design of the tool drawer should work for Ender 3 v2 as well. The design is intended to use the original "case" for the tool drawer but...

Remixed from: https://www.printables.com/cs/model/115518-biqu-h2-ender-3-v2-mounting-plate-with-bltouch Intended to be used with: https://www.printables.com/model/114869-biqu-h2-extruder-part-cooling-duct-mount and...

Model description: Housing for LED strip for Ender 3 NEO printer.I used an 8.1 mm wide LED strip, 6.2 mm wide LEDs. I bought it here. Description of bodies:  Body1 - are two slats that are glued (optional) together at the bottom.  Body2 - is a cover...

This is for an Ender 3 Neo with the extender 400 ender 3 pro kit . you will also need feet on the printer, I got mine here https://www.thingiverse.com/thing:5522084 . This is designed to house the 4.2.2 mainboard and a 120mm thin fan . I am hoping I...

... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...

tool holder for the tools supplied with the ender 3 + a cutome case

My cover break apart after many times disassembly so I remix this replacement part. ... Original design: https://www.printables.com/model/377901-ender-3-s1-x-motor-cover Print like image to save time & have better tolerance.

There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...