ender 3 v2 neo print quality 3d models

Simple remix of tool holder (second design) modified to fit Ender 3 V2 Neo Nothing changed except trimming the inside of the SLT to fit the V-slot How to mount it: 1) Remove the cover of the top v-slot (on the right). 2) Slide tool in. 3) Enjoy...

This support has been designed for those who, like me, own an Ender 3 V2 Neo and have added a Creality filament end sensor. Impossible to find on platforms so I designed a perfectly functional one. This pack includes: Stand The pulley The screw...

... I'm not entirely sure if the dimensions of the profiles changed between the original Ender 3 and the Ender 3 v2 Neo, but at least on my unit, the slots in the profiles do not match the dimensions in the blueprints available from Creality on GitHub.

This is a direct replacement hotend cover for the Ender V2 Neo. It works with the standard fans only. It lines up with the blower fan intake better than the original. I added 4 LED's to the eyes and below to light up the print area. I use 2k ohm...

Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for me but it still works and holds it together. This has printed perfectly for me and works 100% as it was intended. ... ...

Modification of the E3V2 design to fit specifically the Ender 3 V2 Neo Recommendations: a) Connecting the autostop switch in parallel of the printer switch (i.e. ...connecting both switch pin to pin), and not serially (as suggested in the original...

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

Ender 3 v2 led top and side led bar The installation was made with a 1 meter led 5050 strip

All credit goes to the original creators - I simply added a couple features and modified them to fit my printer. This was designed for and tested on my Ender 3 V2 Neo with a Spider 3.0 Pro hot end. UPDATE: I started having issues with getting a good...

This is how I upgraded my Ender 3 V2 Neo to print high temperatures. All dimensions remain the same. Disclaimer: * Do at your own risk. This increases the risk of a thermal runaway and printer damage. * Forget the warranty. * I am still...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

Printed with: Ender v2 neo

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

this is mount works for the ender3 v2

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

This mount is for if you have modified the printer to a direct drive extruder and the filament routes up.I wanted a reel mount that would fit in my enclosure without impeding the side wall, allowing me to centre the printer.I printed each piece...

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

This is an easy-to-print storage tray for an Octopi - tested to fit a Raspberry Pi Model 3b. ...No support should be necessary printing from the face down.

I loved this design but the scraper jingled against the gantry while printing. I added a triangle to the bottom to hold the metal blade away from the gantry upright. Printed in about 30 minutes. Update 08/04/2023 I oriented the print file properly.

Just another filament guide. ...slip on, so no need for any tools or bearings. print without support, and put in place

... the fan noises, caused by air being sucked through grids. ...I also uploaded a split model, with 4 parts which can be printed independently as to not require a single long print. ...Uses a single threaded insert and two self-tapping screws for the fan.

You will need 8 pcs. ...It's flush with the surface. It prints fast and uses very little material. ...You don't have to disassemble anything to put it in place.

I remixed the robot cover to be able to use with out threaded inserts, I also chopped off the antenna to make print easier and look better. ...Also a couple other things to make for less supports.