ender 3 v2 neo print quality 3d models

made a print in place filament guide that changes angle and it is plug and play with the frame of an ender 3 neo max.

Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a 1 degree...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...

This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

Top filament sensor all push fit with gap at back for wiring, made from micro roller lever switch KW12-3 and 608zz bearing. See picture for wiring to sensor (pin 1 and 2 on the board) (outer pins for the switch) Top filament cutter with a drawer...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

PSU cover - https://www.thingiverse.com/thing:4662559 Mainboard cover - https://www.thingiverse.com/thing:4683915 For myself, I cut it into 2 pieces for easier printing with no supports. I included the 1 piece version if you so desire. This should...

**Note:** This solution will only allow you to match the print quality you get when printing directly from the SD card in your Ender 3. If you still experience issues after implementing this solution, then you need to look at your slicing settings...

Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports

Box for Orange Pi 3 LTS, power supply, relay module, DC-DC module for LED strip. Cooling by a fan 6010 12V, powered by a 5V power supply. ... Orange Pi 3 LTS...

Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine

Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile

Customized version of https://www.thingiverse.com/thing:5694620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5694620

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/bYWnr0lPTQU

Customized version of https://www.thingiverse.com/thing:5694620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5694620

Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.

Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...

This was designed to show a resemblance to the ender 2/ 3 Neo extruder cover. If you don't want the 2 color print, I've listed another file, Fan Cover V1, for printing without support. If you want the multicolor though, I've included a sliced file...

Designed a Deck to hold miscellaneous materials while I'm printing or monitoring a print.

fixed the problem where the drawer rails were no printing right and not shown in cura.

I Printed the tension covers and wanted the same design as a dial. Using Meshmaker i combined the 2. I am printing them in gold and wanted to add a C3PO to the dial. I have attached both. I'm printing at 100% infill. ...I dont think it needs this...

3D printer increase Interesting when a larger fan is installed on the mainboard, which has a higher installation dimension. ... Simply print out and glue on the existing rubber feet.

This was for me to use the button with just one finger when printing it I would turn it upside down think this way you don't use support it's not for the looks just to make the turning of the button more fun