ender 3 v2 neo print quality 3d models
2076401 3d models found related to ender 3 v2 neo print quality.
prusaprinters
Model description: Housing for LED strip for Ender 3 NEO printer.I used an 8.1 mm wide LED strip, 6.2 mm wide LEDs. I bought it here. Description of bodies: Body1 - are two slats that are glued (optional) together at the bottom. Body2 - is a cover...
thingiverse
Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...
thingiverse
A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...
thingiverse
It is a filament guide for the Ender 3 Neo (v1) that snaps right into place. It sticks out to the left of the printer by about 10cm, guiding the filament nicely in an arc instead of it going straight down. ... Sliced with Cura - Note: Support...
thingiverse
I couldn’t find anything to my liking that fit the Ender 3 Neo 3D due to the wider stock hotend. I used the the stock screws for the hotend and one of the blower fan screws to hold this in place. M3 screws and heat-in inserts to hold the fans in...
thingiverse
I took his overall design and ideas from other filament guides specifically for the Ender 3 models and made a model for the Ender 3 Max Neo. For my final design, is designed it to mount directly under the extruder on the Ender 3 Max Neo. The...
thingiverse
This is for an Ender 3 Neo with the extender 400 ender 3 pro kit . you will also need feet on the printer, I got mine here https://www.thingiverse.com/thing:5522084 . This is designed to house the 4.2.2 mainboard and a 120mm thin fan . I am hoping I...
thingiverse
... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...
thingiverse
My cover break apart after many times disassembly so I remix this replacement part. ... Original design: https://www.printables.com/model/377901-ender-3-s1-x-motor-cover Print like image to save time & have better tolerance.
thingiverse
tool holder for the tools supplied with the ender 3 + a cutome case
thingiverse
After that I just threaded the filament just as before and INSTANTLY went from a struggling feeder motor to being able to print at 200% speed with absolutely ZERO loss of quality or underextrusion. The results were DRAMATIC. I have been able to...
prusaprinters
There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...
thingiverse
Additional parts needed 2@ M4 X 16 screws 2 @ M4 T Slot Nut Fastener This is a top gantry LED mount for an END 3 Max Neo. It pairs with my X Axis gantry LED mount. https://www.thingiverse.com/thing:5931926. This design is good to give overall...
thingiverse
For this mod, You will need: - Motherboard MKS Gen L V1.0: http://bit.ly/2MiIcAz - TMC2208 (a set of 5 drivers; Ender 3 requires only 4): http://bit.ly/TMC2208 - Alternatively, TMC2208 singly, not in a set: http://bit.ly/2MGFmCa - **11.2019** - Now...
thingiverse
This bracket mounts the factory spool holder from the Max Neo to the top rail. You can use the same screw that comes with the original holder. This is a quick prototype that still needs a little work, but I could not find anything similar. ... I...
thingiverse
A remix so that it can be printed without supports, its a bit of a hack done in tinkercad but prints just fine. All I did was shoehorn in a couple of extra parts and rotate 130 degrees. It should be orientated correctly. Hopefully the original...
thingiverse
Print 2 if you have the dual z axis like i do, cannot confirm other fitments so let me know what it fits and I will update the listing.
thingiverse
Ran in to a problem getting the print in the middle of the print bed. Tries software and several different thins. Nothing worked. So we do this old school. Uses a longer screw, M4x10 worked good for me. Mounts to the back of the X axis carrage, using...
prusaprinters
The holder i 1st printed was not adequate, i needed extra space for a caliper, a deburring tool, bottle of isopropanol and micro sd cards.Also i left out some things i did not need.So i got thinking and came up with this design.In the future i will...
thingiverse
It's a slightly redesigned air duct that features elongated mounting pad for 3 strips of 10mm LED tape - https://pl.aliexpress.com/item/1005001681576572.html?spm=a2g0o.order_list.order_list_main.20.36561c24wW8A3o&gatewayAdapt=glo2polthis tape in my...
thingiverse
Added tools that were important for me to have on hand while printing. I did not add the allen wrenches, I prefered to store them in the tool drawer. My holder is designed to hold: Side cutters, nail clippers (for cutting), tweezers, small...
thingiverse
This led light shade prints in two main pieces which should be joined with glue (I recommend gorilla super glue gel) Once glued you then glue the included beauty plate to cover the join. I recommend making sure it slides into your machine before...
thingiverse
BMG feeder bracket with adapter for stock head. (provides a rigid mount). I have a custom case, but in theory it should fit into a completely stock head. Supports required only for connector PET-G is fine. I'm waiting for feedback, I can correct...
prusaprinters
Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.com
thingiverse
I tried to give all the requirements below but if you have any questions join the Ender Extener builders Club on facebook https://www.facebook.com/groups/Ender3XLBuildersCluband @ Jonathan Franklin David Blanke II in a post.Thank you and happy...