ender 3 v2 neo hot end 3d models

This is a remix of https://www.thingiverse.com/thing:4665097 for the Creality Ender 3 v2 Neo because the rubber pads on the Neo were slightly too big to fit into the original design.

This is a remix of a popular tool holder changed to fit Ender 3 V2 Neo. I also added a hole for the brass brush. ...

A neat tool holder that fits all the tools that come with the Ender 3 V2 Neo. ...It fits inside the drawer of the printer pefectly.

This is a simple Screen Cover for the ender 3 V2 Neo Note: Hasn't been printed yet. Please post what you have made at a make. ...

A filament guide for Ender 3 V2 Neo. ... A remix from 6046403, where the funnel is furthest from the threaded bar of the motor.

proste i funkcjonalne do ender 3 v2 neo, nie mogłem znaleźć odpowiedniego, więc udało mi się stworzyć, chociaż zaczynam dopiero zabawę z drukiem 3d

A filament guide for Ender 3 V2 Neo. ...A remix from 6046403, where the funnel is furthest from the threaded bar of the motor.

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update (-27-22 7:30PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. ...Ender 3 V2 Neo X Carriage Model v2.stl

Ender 3 V2 Neo aluminum heat sink only.I have three Ender 3 V2 Neo heat sink (Creality parts number 3205040089) in my possession. All three have same thickness but different width and height. This model is using #1 dimensions.#1. W 41, H 34.2#2. W...

Adapter for installing the hot end of the Creality CR-10 V2 printer on the Creality Ender-3 printer.

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

There seems to be 3mm difference in the offset between the Z screw and the frame when comparing the Ender 3 Pro to the Ender 3 V2 Neo. ... Have remixed MammothMGs design to close that gap.

CREALITY ENDER-3 V2 NEO - HOTEND COVER This is a direct replacement hotend cover for the Creality Ender-3 V2 Neo. It works with the standard fans only and he comes with 3 different front covers. You are also welcome to create your own front covers.

Made a quick remix in blender so it fits Ender 3 V2 Neo printer. ...Just removed the support on one side since the front of the top bar isn't open on the newer printer.

As the Ender 3 v2 Neo has a drawer that allready fits most of the tools i decided i only wanted a holder for the tools that don't fit in the drawer.

... mounting the nozzle tray to the backside of the printer on the top V-Slot rail. ... Ender 3 V2 NEO MK8 Nozzle Tray (V-Slot Mount) - This is for mounting the tray to the side of your printer or of the trop V-Slot rail if mounting to a different printer.

... This design doesn't need to remove PTFE tube and you can use my front fan holder or you own grille design. Here more infos and attributions to the original design: https://www.printables.com/model/465342-ender-3-v2-neo-ez-fan-mount-with-front-frame

The original wasn't compatible with my ender 3 V2 NEO because it has a piece of metal blocking the front space in the frame. I also removed the "ender 3" in the side of the piece. ... Didn't tried, but i think it is also compatible with all others...

Adaptation to fit Ender 3 v2 NEO No screws needed, it fits on extruder plate. ...Print Settings Printer Brand: Creality Printer: Ender-3 v2 Rafts: No Supports: No Resolution: 0.20 Infill: 15 Filament: JAYO PLA + Black Category: 3D Printer Accessories

The Ender 3's Extruder Hot End features a Heat Block designed to precise specifications.

Remix of Boof69's Waste Bin for Ender 3, adapting the great design for the Ender 3 v2 neo. ... Changes: + Height from bin bottom to print bed edge from 50 to 60 mm + Total width extended to 125 mm + Removed the "Waste" type (aiming for a cleaner...

Remix from rosspayn3's Ender 3 v2 Neo Filament Guide. The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. ...This is a filament guide to help the...

... ring vent by Waico. ... This remix fits the Ender 3 V2 Neo. I had to thin out a few sides and move some other things around but here it is! Make sure to have supports set to 87% or higher. ...Supports should only be below the corners for the screws

All credit goes to the original creators - I simply added a couple features and modified them to fit my printer. This was designed for and tested on my Ender 3 V2 Neo with a Spider 3.0 Pro hot end. UPDATE: I started having issues with getting a good...

Created a mount for Ender 3 v2 neo, should work on other ender printers. This needs no mounting hardware to attach to printer. Just take off legs of Sonic pad and use hardware to attach to mounts and slide on printer. ... Hope this helps out everyone...

... to the post. I'm pretty new to designing parts.) V2 Neo Shroud: https://www.thingiverse.com/thing:5610691 Ender 3 Shroud: https://thangs.com/designer/CyJax/3d-model/Stock%20Fan%20Shroud%20Replacement%20for%20Better%20Visibility%20and%20Cooling-23504

I liked the remix @mikelawrencenz made of the side stand angle printer brackets but neither the remix or the original top bar stand by @3d4LeyeF would fit on an Ender 3 V2 Neo due to the top bar having a flat surface with a hollowed out forward...

... I'm not entirely sure if the dimensions of the profiles changed between the original Ender 3 and the Ender 3 v2 Neo, but at least on my unit, the slots in the profiles do not match the dimensions in the blueprints available from Creality on GitHub.

... 7:30PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Ender 3 V2 Neo X Carriage Model v2.stlUpdate 2-16-23 3PM PDT: Added a missing hole at the top right of center on the plate. ...Added second version without V Wheel disks.

I've designed an incredibly basic PSU holder specifically for my Lack table enclosure, which accommodates my Creality Ender 3 v2 Neo. It's crude and simple but it got the job done. The design allows for mounting the PSU under the table's top surface....