ender 3 v2 neo direct drive 3d models

This is a remix that allows you to mount the extruder sherpa mini or sailfin to "Ender 3 v2" along with the E3D V6 hotend and CR / BL Touch. For the remix I used this project because it is very solid, the hotend does not wobble sideways unlike other...

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

There's a version that works with the Ender 3 Cable Chain made by Johnniewhiskey. The xz versions are meant to be used with the extruder cables and the x-motor cables. ...I haven't tested the xz versions since I no longer have the extruder cables linked...

edit: mjolnirsatsana_bltouch_endoscope_final3.stl has an additional nut cutout on top for using a longer screw through the direct drive mount, this prevents the direct drive from lifting up when extruding fast, and dropping down when retracting. ...

Direct Drive will improve the quality of prints and significantly reduce the printing time of complex models. The double Z axis drive with the frame stiffening allows for precise adjustment of the angles and minimizes frame vibrations, which...

These are just some low profile versions of the Top Mounted BTT Smart Filament Sensors for the Ender 3v2(https://www.thingiverse.com/thing:4918462). I've added an inverted version too, and a new mount for the 2020 extrusion. This is so the mount...

This design is made to accommodate the position of the filament sensor for direct feed. I matched the screw holes to the sensor I purchased. Other models may require a different position of the screws. ... The device is adjusted to the top profile of...

... 4 holes M4, for any improvements later, like aditional filament guide, or filament runout sensor. 3 holes for filament sensors are 8 mm diameter, top of holes are 9 mm diameter for around 5 mm height. ...Used M4 tube holders with longer body.

NOTE: Been on 3 days, just finished a 30 hrs print, perfect, but led's are suffering a little sag and when they were warm ive had to push them back into there holes, but theyve settled in with a tiny bit of droop but are fine. I will at some point...

NOTE: Been on 3 days, just finished a 30 hrs print, perfect, but led's are suffering a little sag and when they were warm ive had to push them back into there holes, but theyve settled in with a tiny bit of droop but are fine. I will at some point...

Print with ABS or any temperature resistant material as the extruder motor temperatures can go upto 90 to 95 degree C. You may find holes a little smaller for metal tube piece to fit that is on the screw between roller and carriage plate. This is...

I ma not sure if HKFEVER made a file for the stock extruder, but this is for the stock extruder on the E3MAX.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I would suggest printing this with the angled face flat on the bed; that way the force of the weight of the motor isn't completely perpendicular to the layers. ... I'm fairly new to 3d printing and couldn't easily find a model for moving the motor to...

This design replaces the standard Ender 3/3 Pro spool holder to one suitable for use with a Direct Drive hot end. The original spool bracket is retained. In my case, I have a MicroSwiss direct drive which still used the original Bowden tube set-up.

Printed with: Ender v2 neo

I wanted a low-cost direct drive that was robust enough to print flexible filaments on my Ender 3 Pro and use the Bullseye duct at the same time. So, I decided to combine them into one unit. I strongly advise using tree supports in Cura when...

... bracket. Feel free to modify it to your liking, I wanna see if this print helps you and if not what modifications you made to improve it! :) It also as enough space for a motor heat sink! Compatible with Ender 3/ Ender 3 pro style x carriage plate!

work in progress. ...hot end housing using stock ender 3 v2 mount. hot end cover for this type of ender 3 v2 neo hot end using stock fans from ender 3 v2

this is a compact direct drive mount for the well-known bmg (clone) extruder with a small stepper motor (17HS4023) on the left side. you can also use the stock stepper motor - but that puts too much unnecessary weight on the slide plate and print...

This is a streamlined direct drive mount designed specifically for the popular bmg clone extruder, paired with a compact stepper motor (17HS4023) situated on the left side. For optimal results, consider using the small motor instead of the stock...

Direct Drive Extruder Filler Ender 6 v2 fix remix

This is a compact, direct drive mount for a left-hand dual drive (CR10, Ender3, https://banggood.app.link/vcjMiGuOH3) with the stepper motor (17HS4023) located on the rear side. The space between the stepper motor and frame measures 2-3mm at the...

this is a compact direct drive mount for a left hand dual drive (cr10, ender3, https://banggood.app.link/vcjMiGuOH3) with the stepper motor (17HS4023) on the rear side. there are 2-3mm between stepper motor and frame on the outer positions of the x...

... ...This now accommodates the additional width (90mm) required for dual drive extruders. I also incorporated a Dragon. Dragons are indeed cool. A non-Dragon version is available, but who would want that? ... Update 07/05/20: BL Touch Versions Added

ender 3 neo cooling dock for Noctua 40x20

Simple nozzle cooling air duct modification for Ender 3 Neo or Ender 3 V2 Neo, to provide improved and even cooling from all sides. ... Very clean and simple print with no supports needed This is a remix to fit Ender 3 neo printers from: DJIFF Edit:...

I couldn't find a Wyze V2 mount for my Ender 3 V2 Neo that did all the things I wanted so I made one. Attaches to the front with the factory screws. The actual V2 mount plate was made by jitterzPrintz and can be found here...