ender 3 v2 neo direct drive 3d models

Probably only needs 2 but 3 looks cooler :) print with supports everywhere I hope you enjoy this mod as much as I am after making it. Make sure to raise your hotend as high as it can go before putting the harness in the print to prevent any stress...

Different versions, pick the finer oneThis design includes 3 different models that used a different resolution setting in the software for the optimization. Highly recommend you take the Finer one if your printer is tuned, if you are having trouble...

This mount is for if you have modified the printer to a direct drive extruder and the filament routes up.I wanted a reel mount that would fit in my enclosure without impeding the side wall, allowing me to centre the printer.I printed each piece...

... printer start the belts through the bottom of the carriage. - Secure carriage to linear rail block with M3x8 (x4) - Crimp belt and tension See Ender 3 V2 Direct Drive link below for extruder install info https://www.thingiverse.com/thing:4621486

This is a remix from https://www.thingiverse.com/thing:398515 -Edited back plate to fit ender 3 v2 with more route for cable. -Remove slot for M3 nut. -Add Bltouch mount closer to hotend for better accuracy. offset (28, 13.5, 0) -Edit prusa air...

This is a modification for the " onodono" design -link below. ... Added holes to make use of Ender 3 V2 BLTouch mounting holes for extra rigidity. ... BLTouch mount itself has been thickened to make it extra resilient to to any kind of movement

(probably last version :) and only for direct drive) This design uses 32 additional metal pins (fi 2mm, length 8mm) on which steel balls are placed. Number of steel ball per layer was also doubled (4 per layer) to create full working plane. ...

... with middle part. All magents needs to attract each otherMount device on Ender and enjoy :)Print SettingsPrinter Brand: CrealityPrinter:  Ender 3 ProRafts: NoSupports:  NoResolution: 0.2Infill:  20%Filament: Fiberlogy PLA Black

Remix of [JamieBK's direct drive mount](https://www.thingiverse.com/thing:4555065) that uses the dual gear drive extruder used with CR10

Hey all, made a remix for the direct drive since I was using a satsana I needed to make it higher(around 5 mm) here is the result. V2 added place for cable tie. V3 added 10-4-21, for the cable link system, check my other designs. Added...

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

Remix for use in Unitak Direct Drive Upgrade Kit for Ender 3v2. https://www.amazon.com/gp/product/B09KG8MMQ2/ref=ppx_yo_dt_b_asin_title_o03_s02?ie=UTF8&psc=1 *The part was rotated 2 degrees to align with the mounting plate. *Added support...

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

I knocked together a silly filament guide that mounts to the NEMA17 (31x31) plate where the extruder motor used to be on my Ender 3 V2. This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I...

this is mount works for the ender3 v2

This is the link to the Voron M4 DD for E3V2 https://www.thingiverse.com/thing:4901100 And Hero Me Gen 5 (Ender 3 V2 Stock hotend) https://www.thingiverse.com/thing:4460970 Ik it's pink in my photo. ...I don't care abt color since this is for work and...

This is a modification for the " onodono" design -link below, to suits the BMG extruder in the picture above for Creality Ender 3 v2 using stock hotend pricket with Bl-Touch mount Credit/Original thing link: https://www.thingiverse.com/thing:4576440...

... i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

... that i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

I knocked together a silly filament guide that mounts to the NEMA17 (31x31) plate where the extruder motor used to be on my Ender 3 V2. This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I recently...

SummaryA fan shroud that is compatible with a sideways direct drive mount, with the extruder motor protruding on the left side.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

Direct drive side mount for stock motors, fits nice and snug, and added a hole to tighten with m3x20mm bolt. mechanical part so high infill recommended. ... no support needed.

This is a remix of the default Creality mount. ...Offset to allow for use with direct drives. ...You may need to force the screws a bit or lightly drill them a touch wider.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...