ender 3 v2 micro center 3d models

A micro sd card for the ender 3/v2 It can hold up to 16 micro sd cards.

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

As a result, only one of the two screw holes on E3D's fan shroud will line up with the holes on the Ender-3 V2's X carriage.I added an extra screw hole in the model, which aligns with the hole on the Ender-3 V2's X carriage. ...The mounting screw for...

I combined this with a mount to attach it to my side rails on my Ender 3 v2. ... I installed it on the left side of my printer, you'll need to remove the 2 fronts (LARGE) screws and 1 screw at the bottom.

This was made for the top of the line ANKER Micro USB cable. Once you have it smoothly moving in and out of the opening (while not plugged into the printer) slip your cable through the opening, and apply some hot glue to the back. Plug the cable in...

Meant for the ender 3 v2 y axis pulley. ...If your y axis belt is not perfectly centered on the pulley and/or rubbing your frame these simple rings will fix it.

Ender 3 V2 micro sd extension cable holder, printed with PLA+ at 215 degrees nozzle temp and 60 degrees bed temp.I just use the extension so that the micro sd slot on my printer doesn't get worn.

***"Micro USB Fist Hanger"*** ***Connector Protection (Ender 3 v2)*** --- A simple mix of : *- [USB Cable Holder Fist](https://www.thingiverse.com/thing:4293411) by blackguest* *- [Ender 3 v2 USB Port...

Dock for memory support -USB (1) -SD (4) -MICRO SD (1)(4 inside sd) Rails available for perfect fit in ENDER 3 v2 (tested) DIMMENSIONS 56mm*40mm*43mm (approximate)

This is a spacer for using the Creality Ender 3 V2 BLTouch kit with an all metal Micro Swiss hot end. The Micro Swiss sits a bit lower than the standard hot end. ... Z-Offset of -2.08 worked for me on my machine with this spacer.

This is yet another micro SD card holder for the Ender 3 and Ender 3 V2. I have 2 SD cards that I swap between the 3D printer and my computer. When I pull the card out of the printer I needed a place to easily store the card while I set up the...

This is an Apogee shroud modification for an "Ender-3 V2 Neo" with a "Micro Swiss hotend" (not usable with the original Neo hotend). Unlike the original Apogee shroud, this modification leaves the CR-Touch mount on the left side. This also means...

ENDER 3 V2 MICRO SWISS DIRECT DRIVE AND HOT END UPGRADE. So I got my Micro Swiss direct drive and hot end upgrade but didn't like the cooler shroud that needed to be printed as it utilizes the single 40-10 part cooler fan. I wanted to increase my...

Straight forward wire management links for an Ender 3 V2 with a Micro-Swiss NG direct drive extruder. I provided the STP files so anyone can edit them to their liking.&nbsp;</p><p>&nbsp;</p><p>You will need a total of 10 links. I used zip ties to...

I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the original shroud does not fit the bracket. There are few other minor tweaks and optimizations I've done on top of the original AYF...

This adapter will fit for the Ender 3 Pro V2 Compact SD Card Adapter Housing V4 https://www.thingiverse.com/thing:4609997 I`ve designed this to fit a microsd extension in the sd slot. ...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

4 usb holders and many micro usb holders

I created an micro-usb-port support that's easy and fast to print. It's main objective is to protect the port when a cable is inserted. Just put a dab of hot glue on the thin flat side and glue it into place. Scared of hot glue? Or maybe want to...

... This makes for a better mesh in my opinion and it just looks cool. 3. Designed a new mount for the BTT Smart Filament Sensor. 4. ...Redesigned the top hat to accommodate the wiring harness a bit better with the addition of all the extra stuff.

Micro swiss direct drive extruder fan holder for ender 3, ender 3 pro and ender 3 v2 with x-axis correction. This is two part body (part no. 1 and part no. 2), after printing two body must stick together with plastic adhesive glue. This is because...

Hello all, This is a MICRO version of the Ender 3, designed to create an "Inception" feeling by being even smaller than the Mini Version. No support needed for this print; you can do it in one part or multiple pieces. A square supporting the Y axis...

FANG Duct with Center mounting BLTouch for Aquila and Ender 3 V2 and 3 Pro This was an experiment that turned out well. I have placed the BLTouch in front of the Extruder in the center. This allows for the entire build plate to be probed. I have...

Ender 3 V2 Neo X-Limit Switch Housing for Micro Swiss NG

Ender 3 v2 SDHC card, micro SD and USB stick holder for 40x40 profile.One of my first projects. ...Easy, useful.</p>

The location of the Micro SD card slot on my Ender 3 is a bit off-center. I'd say it's actually better suited for an SD card, if you ask me. Here's a micro SD to SD adapter I bought from Amazon that would work perfectly in this case. ... Check out the...