ender 3 v2 linear rails 3d models

It is for Ender 3 printers with the upgraded X-axis with the aluminum backplate, which mounts on the two M3 screw holes on the left side. I have a cut-out to fit the Fang cooler around. The dial indicator is specifically the digital one by...

Use them to space the linear rails from the top 2020 extrusion. This is designed to be used with direct drive. I am using a Biqu H2 extruder but it will work with others obviously. You must print at 100% infill. I used 0.2 layer height. This set up...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

All the linear conversions I had found for my Ender 3 necessitated drilling of the Y plate. I prefer not to drill additional holes unless absolutely necessary, so here is my solution, including a simplified Y axis endswitch holder. V2 IS NOW...

Y axis Linear Rail for ender 3 Series. Its not perfect. ...maybe you can contact me for i revised

Y axis Linear Rail for ender 3 Series. Its not perfect. ...maybe you can contact me for i revised

This is a fixed version as the original clashed. ...I could not edit that "Thing" so made another. See a photo of it in use on my Ender Pro with 2x MGH12 Rails.

This is designed to be used with direct drive. I am using a Biqu H2 extruder but it will work with others obviously. You must print at 100% infill. I used 0.2 layer height. This set up eliminates the need to recenter the build volume after...

This version is made to work with Ender 3, Pro, V2 and Aquila printers and uses the stock X Gantry Plates. The Drive/Motor mount has 2 versions to accommodate Stock and dual extruder drives. I have used this paired with my Z Linear Lift Mod that is...

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

Full design of my setup with linear rails assembly Need to invert motor rotation in firmware This is my setup, maybe if you want change some parts you have all files to do

Linear rail installation on all axes of the U30pro List of parts and supplies to be purchased : 1x rail MGN12H 300mm with trolley 4x rail MGN12H 350mm with carriages 2x trolleys MGN12H 2x profile 2020 250mm (T-slot or V-slot, no difference in use)...

The goal was use a Bondtech LGX extruder in a direct drive configuration with the Ender 7 Style dual 4010 fan shroud all mounted to a printermods MDD v1.3 plate with linear rail conversion. I am not an expert at 3D modeling so some filing and...

MGN9C or MGN9H X-axis linear railM3 heat inserts Toolhead for :stock daughter boardstock 1x5015 part coolingstock hotend or E3D revo-cr hotend (not tested)New hotend fan coverV2 new :Adjusted 1mm higher belt position. ...Clamps adjusted.New hotend fan...

I remixed this for my Ender 3 Pro with x, y, and z linear rails. I modified the cutout in the middle because there is more depth to use under the y-axis with the y-axis linear rails. ...I also used a 0.6 nozzle to print 0.4 lines because the extrusion...

Biqu H2 adapter plate for Ender 3 with [linear Rails](https://www.thingiverse.com/thing:3031918). I added space for Cables as well as holes for Cable Ties. Integrated ABL Sensor holder for a Ø18mm inductive probe. You need (additional to the Screws...

... to The Ender 3 you need to swap the outer screw holding the Z-Stent to the original extrusion for a 30mm M4 Screw. The Part is Designed so you can melt a threaded insert in it and screw the Tensioner the Linear-rail-Plate and the Z-Stent together.

Update 05.08.2023 Modification to mount a Hemera XS Revo extruder on an Ender 3 (Pro) with linear rails. Only M3 melt-in threads and screws are required. The M3 screw is required on the left to release the limit switch. The limit switch needs...

Put the adapters on the linear rails with (4) 3 mm screws. Center plate on adapters. Make from below for holes. Then drill out holes and mount plate on adapters. The belt adapters mount flush to the edge and drill holes and mount them. Belts...

When I upgraded to the 3D Fused Linear Rail Kit, I found that the guide would no longer fit due to the width of the spacers installed with the new rails. I downloaded the STL file for the spacer off the 3DFused website and using Tinkercad, I opened...

When I upgraded to the 3DFused Linear rail kit I found that the guide would no longer fit due to the width of the spacers installed with the new rails. I downloaded the .stl file for the spacer off the 3DFused website and using Tinkercad opened up...

... mashup of two excellent files. ...Thanks to the creators! Untested as of now. I will make updates if needed although I doubt there will be any issues. Additional parts are needed so see the Belt Driven Ender 3/Pro/V2 and CR10 page for those files.

Used 2 linear rails 350 mm MGN12 from Amazon. M5 bolts 8-10 mm (12 of them) or reuse the ones holding rollers with nuts. As the rollers are removed, it made a space for side light in side right V-rail (connected to an existing switch for the top...

Niskyspy has one of the best-designed Hemera/linear rail mounts I've found on Thingiverse, mainly because he actually included the belt slots (why use another mount?) What I'm using in production: E3D Hemara-railonly-short-xstop = This is a shorter...

This mounting guides are for the linear rails from AliExpressX axis has a width of 9mm and Y axis is 12 mmLink: https://www.aliexpress.com/item/1005004944650633.html?spm=a2g0o.order_list.order_list_main.5.3f5c1802ayKkvxInstallation:...

... bolts to m5x.80x16 bolts. added two holes toward the middle if you want to drill for even more stability (unnecessary) . Printing: 30% infill uses PLA. the ender 3 max is insulated - i also have pla on my regular ender 3 - no issues.

This is a remix of the x axis plate for MGN12 linear rail mod by BobbleJot (Thing:3489410).\r\nhttps://www.thingiverse.com/thing:3489410/\r\n\r\nI had a problem attaching the hotend to the plate, just like others who have used this...

An upgrade to fix the not linear Y Axis extruded bar