ender 3 v2 hot end 3d models

Here's a straightforward mount for a BL Touch sensor on your stock Ender 3 hotend. I created this because existing mounts were a bit too flimsy for my liking. This one boasts a thicker design and features strategically placed cutouts on the backside...

... (and to prevent melting during ABS printing). Although hot end cooling efficiency is slightly reduced, the time constant for "cooldown" increases by only 25%. ...This reduction can be attributed in part to not blowing directly on the heat block.

Visit the Ender 3 Cable Chain by @Johnniewhiskey in the Remix Sources section to get the files for the chain links. Enjoy and post your makes! If you found my Things useful, treat me to a cup of coffee by using the PayPal button below. ... Buy...

A simple and easy-to-print solution for securing the Ender 3 Pro's x-axis gantry. Secure your bowden tube and cables with two zip ties to keep them vertical, thereby preventing damage to the cables and reducing the risk of the bowden tube coming...

This appears to be a Thingiverse post describing a custom cooler design for 3D printing, specifically for the Ender 3 printer. The author has created multiple versions of the cooler, including single and dual-blower front housing designs, as well as...

This part is design to direct the air flow to the heatsink of the hotend on Ender 3 and other similar model to provide better cooling and hence reduce chances of heat creep. It also prevents the fan from blowing directly to your printing part, this...

... hex nuts is available to support BL Touch mounting. ...However, this particular configuration was too low for my MicroSwiss all-metal hotend, so I created this remix approximately 3.5mm higher than the original mount, resulting in seamless performance!

I found some hot covers for the spider hot ends for the ender 3, however they didn't fit. Also, printing with green Tglaze, the effect is awesome. Ensure to hot glue the hulk cover. ...

**Printing Instructions** I use 210c degrees on my PLA with stock Ender 3 V2 hot-end, build plate at 60c Standard quality, 0.2 millimeter precision This should be printable without supports, I have not tried the whole thing without supports, but I...

Circular hot end fan duct for Ender 3v2. ... This duct does require some modification of the stock cover to accomodate the fan.

Creality Sprite extruder hot end fan duct

A simple hot end fan shroud that draws air from above, not the front, preventing stringy filament from getting sucked in. It just clicks right into place at the front. I removed the sticker on the front first, which might affect how well it fits.

This is specifically for the housing on the Ender 3/Ender 3 Pro/CR-10. Printed with .2 resolution, 20% infill, and I actually used a full raft which helped with the support removal. Supports (touching build plate only) were used at an overhang...

This is specifically for the housing on the Ender 3/Ender 3 Pro/CR-10. Printed with .2 resolution, 20% infill, and I actually used a full raft which helped with the support removal. ... Supports (touching build plate only) were used at an overhang...

The chill factor drops significantly at the cool-end section, yielding a substantial improvement in the cooling process.

I liked the brackets by modrows1, but the holes were off on my machine, and I didn't like having to use a nut. ...I threaded one of the 3 holes on each of the brackets, and tweaked the positioning to match the needs of my printer.

I'm sure some washers printed on100% infill could work also.* *NOTE 2: I only used 25 link covers on the Z axis because I left one off where I let the ribbon cable escape the chain 8 links before the Z cable chain connects to the extruder mount.*...

From Slim X Axis Cable Chain with Extruder and Hotend Mount for Ender 3 Pro (https://www.thingiverse.com/thing:4314829) extruder-mount-28mm-alu.stl slim-link.stl x 17 slim-link_cover.stl x 17 From Ender 3 V2 Hot End Slim Chain x Axis Mount...

See the latest version here: https://www.youmagine.com/designs/mikes-hot-end-v2-5, along with its accompanying water block at https://www.youmagine.com/designs/triple-water-block. The designer modified his previous design to work for 1.75mm filament...

Ender 3 V2 - End Cap ready for switch. ... I use this as my light bar on off switch

5015 blower mount for the stock Creality hot end to allow the blower to pull air from behind the hot end. In this orientation the hot end cooling does not interfere with the part cooling efficiency. 11-6-20** Added a reverse or "right side"...

... 2. Lightly screw the nozzle in place, then heat it up to 250C before final tightening. 3. Once cool, screw on the nozzle nut. 4. Insert the liner and tighten the push-fit connector onto it; the connector may need removal when mounting the hot end.

An end cap for the 2020 aluminium extrusions on the Ender 3 V1 and V2, not sure if the Ender 3 Pro has the same sizes so its not included however may work. I printed it "Dwayne" up. ... I slowed down the print speed once the printer got to the head...

I've installed an all-metal hot end with straight edges, a significant improvement over the stock Ender 3's circular design. To accommodate this upgrade, I've increased the gap between the hot end and the printer frame. Additionally, I've added an...

I have an Ender 3 V2 and switched to stiffer yellow springs. They were a bit longer than the stock springs and would cause the nozzle to crash into the bed even with the springs tightened as far as possible/bed as low as possible. Originally I just...

First design, required some adjustments in Cura to flatten the top. ...Printed with an ender 3 v2. ...Hot end: 200Bed: 50Filament: Silk Violet PLA+, 1.75

Added a Micro Swiss Ng with Revo and wanted to make it easier to attach the cables, swap fans without cutting cables so added wago's and generally gave the cables more support. ...Wago lowered in V2 to give more stability 28/02/2024

Remix of BL Touch on a stock Ender 3 hot end, because one BL end live of my Geeetech brander TL-touch sensor. make about 1mm z-axis clearance between sensor and hot-end. ... remix of - https://www.thingiverse.com/thing:3557973

You can install this Ender 3 hot end clip with the original screw. The previous version was too thick and tight for use with the original screw. The extruder end clip has been modified for easier movement of the extruder. ...Its shape now allows for...

This is my custom ender 3/CR10 fan mount for my V6 hot end. you need 3 3x20 screws for the hot end fan and 3 m3x20 nuts and screws for the parts cooling fan. It should be adjustable to your height, but no guarantee. ... Works for me better than the...