ender 3 v2 fimrware auto leveling 3d models

I built flat covers for my ender 3 v2. The fronts fit exact size. The back one fits with the motor and if you have only one motor in the back use the front one. it will be the same size. I did mine in silver then painted it. I added a picture of what...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of the...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

I really liked the design Ender 3 V2 Scraper & Snips Holder from ahuczekdesign but I tend to use a glass scraper more than the paint scraper so I added an extra wide slot for that to fit snugly in to place I then decided that as I us the Needle nose...

Needed some feet for my Ender 3-V2 after upgrading the PSU fan and printed this cover for it : https://www.thingiverse.com/thing:4567153 These feet are simple and clean and fits over the rubber feet that are on the printer. There are two versions...

The Aim of this project was to build a converter kit for my V2 model into a Core YX printer and by reusing as many original parts of Ender 3 v2 as possible. The second goal of this build was to keep the possibility of converting back the coreYX to...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

Top left holder with 2 sections 1 designed for paper offcuts for levelling with a paper template to cut around. Top middle drawers for odd bits and to fill space one with an open top. Enjoy would love to see some makes! :) Happy...

Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...

Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile

Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine

... so desire. This should work on the 3 & 3 pro, but I think the rubber pads aren't as thick. You might need to shave town the top edge or lose the dampening of the stock rubber pads. ... Fusion 360 files included, I don't care if you hack it up.

This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.

 No more, finally able to address this problem and I am sharing my experience here in the hope it helps some others.Many people have trouble getting a first layer and it seems especially so with the Ender 3 S1 and the CR Touch.  You do...

Don't use these GCODE files on anything else than the Ender 3 V2. Even though it might (and even should) work on other printers with similar build volume, I haven't tested it on any other printer. Please ignore the STL file, Thingiverse won't let...

Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports

... When you have printed it you just relevel the bed with the part under the z endstop If you already have your bed level perfect and you don’t want to start over you can just fill it down so it fits. This isn’t some fancy model but et helps a lot.

Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.

Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...

I modified Chris's test to fit the Ender 3 V2. It is designed to work within the 235x235 bed and prints at 220x220 so it stays away from any clips that are used to hold the bed in place. Edit: You may need center the model and then shrink to 99%...

  This İs Gcode Fİle

Remixed the Ender 3 Max dual z height sync spacer from scratch to fit the Ender 3V2. So basically I took the idea and made a new version to fit my needs. Used to sync the heights of your Dual Z axis. And can also be used to help set the Z axis...