ender 3 v2 filament 3d models

This is a 70 mm wide spool holder for Ender 3 v2 using the original nut for mounting. All parts are 3d printed and it has no bearings. It is inspired by several other Ender filament spool holders. The roller and bolts should be printed standing.

This design was made to recycle the included bearing on the extruder, mine broke and decided to use it to create my own filament guide, this design was remixed from previous model and adjusted for perfect fitting in Ender 3 V2.

Made this for my Ender 3 V2 to top mount a Creality filament sensor. I used the original creality M3 screws for the filament sensor and then 2 M4 x 16mm screws for the swivel joint. You need to adjust the tension on the 2 screws so it positions it...

I bought an SD reader from Amazon, to fit to my Ender 3 v2. I put rails on it, so it would sit on the left side of the base. I made it a fraction bigger to aid fitting the reader. Tightened/fitted by wrapping Masking tape around it. Also on here,...

I printed out a Side Spool Holder for my Ender 3 V2 and realized my normal wheeled filament guide wouldn't cut it since the spool holder wasn't on the top anymore so came up with this simple guide that is mounted on the Z access screw guide using the...

Im running jyers ui to enable filament run out sensor in my ender 3 v2. This wont work with previous enders unless youve updated mother board to v4.4.2 or v4.4.7 as these newer boards have port to plug switch into. Great video on jyers firmware...

... suggestions or anything else regarding the design. I printed it and it is installed on my Ender 3 V2 printer and working. ...I uploaded the SolidWorks part files and STEP files too in case you want to use the CAD model or STEP files to do a re-mix.

The original clip was loose on my Ender 3 v2 frame. Some people suggested scaling it up 101-102%, but it didn't work well for me. I redesigned the clip by scaling the rod and inserts 105%, and moving them closer to the center 0.5mm, but kept the...

Ender 3 Filament Runout Sensor for Z limit switch This is a remix from https://www.thingiverse.com/thing:3858309 #### Instruction This modification allow the filament runout sensor to pivot has the extruder head require it. The original screws used...

I edited the arm from here https://www.thingiverse.com/thing:4745849 for handling better the filament, also avoiding unwanted slip by cutting the slit at 45 degrees.And using the frame clip from https://www.thingiverse.com/thing:4321023.Added an...

I edited the arm from here https://www.thingiverse.com/thing:4745849 for handling better the filament, also avoiding unwanted slip by cutting the slit at 45 degrees.And using the frame clip from https://www.thingiverse.com/thing:4321023.Added an...

Adapted the Ender 3 filament guide / runout sensor to use to printer's original z stop. Uses a 6608 bearing for the roller. Print 2 of the spacer, and one of everything else. If you have a 5mm bearing, use that. Otherwise, you can print it. ... ...

Print Settings Printer Brand: Creality Printer: Ender 3 Resolution: 1.2 Infill: 15% Filament: Generic PLA/PETG/ABS Black Notes: You may need cleaning the piece to fit the base and cap, depending of how much accurate your printer is. It doesn't need...

Filament Sensor: BigTreeTech Filament Break Detection Module For 1.75mm https://www.aliexpress.com/item/33028816768.html Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: Doesn't matter...

Edit 5/21/21: Modifed mount to use less plastic and better align horizontally with the extruder. Adapted the Ender 3 filament guide / runout sensor to use to printer's original z stop. Uses a 6608 bearing for the roller.</p> <p>Print 2 of the spacer,...

Eléments basés (mais redessinés) depuis les sources suivantes: https://www.thingiverse.com/thing:4185537 https://www.thingiverse.com/thing:4683505 https://www.thingiverse.com/thing:4695818 https://www.thingiverse.com/thing:4720152 This associated...

This is a combination of a filament guide and a z-axis stabilizer, without the need of a bearing. It's printed at 100.3% scale and works fine as is. It's abit loose until you attach the screws again. ... The spacers are meant to space the original...

The opening at the bottom is 3.5mm so it can accommodate various filament diameters. It also helps set the filament at a slightly curved angle as it enters the extruder to avoid snaps and tugging problems. You can reposition the guide on the...

Filament Sensor: BigTreeTech Filament Break Detection Module For 1.75mm https://www.aliexpress.com/item/33028816768.html

... Added an extended version of the clip to make it more stable. Added a remix of https://www.thingiverse.com/thing:4304283, made it shorter and have a bottleneck ending for the filament dust filter fit into my filament guide.

I wanted a minimalist design that keeps the filament off of the z-screw, but also avoids any drag on the line.

This is a filament guide that fits on the official Creality runout sensor carriage. ... Only the file for the bracket is included, for the other parts (spacers and ring) use the files from the original project.

Designed for a setup with the filament spool placed downside the printer EDIT: The tube it's a bit misplaced, it should be closer to the Z screw. ...I promise new version.

... scratch in Fusion 360. Switch now bolts on to the back of the bracket. Update 25/03/2021 - Works OK, but positions the filament a bit too high so it rubs on the bottom of the runout sensor. Am going to amend. ...Horizontal alignment is perfect.

My filament kept snagging on the runout sensor, I printed a new housing for it, which improved it but the problem remained.&nbsp;Print this however you wish, use short M3 bolts to hold it to the carriage in the recessed holes, and M3 4mm melt in...

... screws that came with the printer. The connection cable is easy to disassemble and assemble. The wheel at the extreme relieves the tensions in the filament, at least for me was a problem and also prevents the filament touching the lead screw.

... that will accept a 608 bearing. ... The pins are also remixed so that one end will fit snugly into a 608 bearing, and the other will still fit snugly into the roller holder. The result is a really smooth rolling filament spool holder. ...Enjoy!

... by holspeed. ...In my case i've to feed the filament from the side due to space limitations. I just turned the roller in a was that it suited my needs. ...You can find the rest of the needed Parts here: https://www.thingiverse.com/thing:3052488

In my case i've to feed the filament from the side due to space limitations. I just turned the roller in a was that it suited my needs. ...You can find the rest of the needed Parts here: <a...

This is a remix of https://www.thingiverse.com/thing:4683505 with the arm rotated 90 degrees to provide a nice bend for handling filament with a read-mounted spool such as from https://www.thingiverse.com/thing:4333835 The spool holder has its own...