ender 3 v2 fans 3d models

This holder worked perfectly on my Ender 3 v2 satsana duct with angled front fan (10 degrees), and not sure if it will fit other types out there as Mentioned above, this will fit on top of a 4020 fan and any dial indicator with 8mm shaft . I've...

I also recessed the CR Touch screw mount so the backplate could be screwed to the gantry plate while allowing the left 4010 blower to sit flush against the fan duct backplate. Hardware Info: https://www.thingiverse.com/thing:5368944 (Optional:...

This helps when replacing the nozzle The heatsync fan can be held either just by compression, by using a PC fan screw, or (V2 only) by using an M3x20mm screw The 5015 fans sold on the marked do not come with the plug used by Creality. Keep in mind...

This is a 'Ender 3 v2 NEO Hotend Cooling Shroud for 4015 fan cover'

4020 Fan Brace for Ender 3 v2 Phaetus Dragon Hotend mods

This is a remix of the remix! ...This is meant for 15mm fans for the ender 3 v2 neo.

Additional Height to fit the the Notcua 80x25mm fanand chamfers around the screw holes for the flush mount screwsIncludes buck converter mountView original for print settings

I made this remix just because I wanted it to be a little bit stronger, so I expanded the very thn side wall and the little pin at the top ans also made the holes for the M3 insets a bit thicker. ... I also added a little cutout for the CR/BL-Touch...

make a couver in th back

I Remix the Raspberry Pi 3 case from Lazax (https://www.thingiverse.com/thing:3892091) adding rails to use it in the Ender 3 v2 v-slot. Modifications: - Add v-slot rail to Ender 3 v2; - I removed the gaps from the bottom piece - Aligned the longest...

Dual Blower Fan Duct for Ender 3 V2 with Spider Hotend Based on the MBOT3D MK2_Rev2.0 by Ahmad Sunardi, I have designed this Dual Blower Fan Duct for the Creality Spider Hotend V1 installed on the Ender 3 V2 3D Printer. You can install it on a...

Ender 3 V2 enclosure Remix for Orange Pi Zero 2 with expansion board and Noctua 92 MM Fans Remixed from Ender 3 V2 Enclosure box electronics external case by GalvanicGlaze The instructions are almost all same as original post. The exception is the...

**Remixed hot end cooler for the Creality Ender 3 V2** Part list: **dual_5015_fang.stl** Remix of https://www.thingiverse.com/thing:2763931 (V3 dual 5015 fang). Please resize to 10% before slicing. I recommend an initial layer height of 0.12mm and a...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

Please note : will only fit the Ender 3 v2 Neo and not the original v2 as they changed the hotend mounting plate! Huge thanks to the original designer for the effort recreating the stock shroud connectors! I found the shape a bit too wobbly so...

Based on the MBOT3D MK2_Rev2.0 by Ahmad Sunardi, I have designed this Dual Blower Fan Duct for E3D's RapidChange Revo CR Hotend installed on the Ender 3 V2 3D Printer. You can install it on a Direct Drive as well as Bowden setup. The magnetic...

I just recently added a biqu h2 to my ender 3 v2. I went through all the mounts out there and couldn't find a perfect single set of prints for my needs. This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab added...

- You might need some dremeling/filing the stock ender 3 carriage, since it has some interference with the Phaetus nozzle. I didn´t designed this project to work with spacers, but it might work. Try at your own risk. - I designed it to work with...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

Direct Drive Mount for Creality Hotend Unveiled with Innovative Hero V2 Fan Duct Cutout. ... The revolutionary new design leverages every single original extruder motor and screw, ensuring seamless integration with existing systems.

I just recently added a biqu h2 to my ender 3 v2. ...I went through all the mounts out there and couldn't find a perfect single set of prints for my needs.</p><p>This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab...

I just recently added a biqu h2 to my ender 3 v2. ...I went through all the mounts out there and couldn't find a perfect single set of prints for my needs.This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab added to...

I didn't want to toss this perfectly good fan, so I changed the size of the fan intake for the 92mm and integrated a grill as well (I'm not sure who designed this particular grill, but I liked it and I would credit them if I had it). I also added...

After destroying two fans so far, I decided that the Satsana fan housing needed a cover. I looked around at the free offerings and found nothing to inspire me, so here is my version. It is 3mm thick and will work with an original 40mm x 10mm fan or...

I had a clocked hotend (cool end) several times now and wanted to upgrade the fans from 40x40x10 to 40x40x20 to improve air flow. ... This one is a remix with cutouts on the fan side so the air can flow freely.

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

Tapa ventilador para https://www.thingiverse.com/thing:4789305 Dos versiones. ...Sin rejilla y con rejilla

This is a remix from https://www.thingiverse.com/thing:4731421 and https://www.thingiverse.com/thing:4637453