ender 3 v2 fan upgrades 3d models

Unfortunately, after printing it out, I discovered not only were the arm sides asymmetrical but also the underside of the fan cover was flat and far from aerodynamic - or symmetrical for that matter. To fix this issue, I streamlined both side arms to...

Remix of Gabriel3DCaster's CR-10 Fan Mod for Enhanced Airflow. To Optimize Print Quality, Try These Tweaks: - Tilt the duct at a different angle so air hits the nozzle indirectly. ...- Shorten it by 1mm to prevent prints from getting damaged during...

Remix of Gabriel3DCaster's CR-10 Fan Mod - Airflow Optimization. Change the duct angle so the air won't directly hit the nozzle. 1mm shorter to avoid hit the print when printing. Category: 3D Printer Accessories

Another Ender3 Fan cover, but who doesn't like variety Best results at 0.2mm Was made using a CAD model and printed in real life without any problems. Possible to print without support but there is a bit of overhand at the top. Without support,...

This is a CAD model of the Ender 3-V2. This is the original modeling for the Ender 3V2 that is used by others and published on different sites. The measurements and modeling are made from my own Ender 3V2 3D printer which I love and it works like a...

WWW.Fabricando3d.es En Inglés This is a protector for electronic fans. It doesn't require supports, so it can be printed vertically without any issues. Check the image gallery to see how to print it correctly. The inlet part is located at the back,...

This is for ender 3 v2's inside of an enclosure after the PSU has been moved outside of the enclosure. Requires some long M5 bolts, longer than stock M3 bolt for mounting stock Y axis endstop housing, and some GT2 idler pulleys (one toothed one...

feet for ender 3 35x20 Spool holder: https://www.thingiverse.com/thing:4721912

I really liked the design Ender 3 V2 Scraper & Snips Holder from ahuczekdesign but I tend to use a glass scraper more than the paint scraper so I added an extra wide slot for that to fit snugly in to place I then decided that as I us the Needle nose...

I built flat covers for my ender 3 v2. The fronts fit exact size. The back one fits with the motor and if you have only one motor in the back use the front one. it will be the same size. I did mine in silver then painted it. I added a picture of what...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of the...

Secure an 80mm x 25mm fan under the bed by positioning it carefully to avoid snagging on any bed screws. To accomplish this, you'll require a longer M3 screw for attachment. ...Additionally, there's a designated holder within the unit specifically...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a 1 degree...

Added bigger fans underneath my Ender 3v2, so it needed to be lifted. Why did I choose this design? Because I happened to have some chunks of 90x53x300 foam that I was already stacking the printer on. They provided good vibration dampening, but were...

Created parts to avoid having wires hanging all over the place in my Ender 3 S1 Pro after installing the Sonic Pad and Nebula Camera. I've installed the wiring ducts on the back of the machine and a little bridge on top to have all wires routed...

work in progress. ...hot end housing using stock ender 3 v2 mount. hot end cover for this type of ender 3 v2 neo hot end using stock fans from ender 3 v2

A remix of this 100mm fan mod at https://www.thingiverse.com/ because 92mm fans are much easier to find.   Contains a replacement power supply cover and an optional 92mm fan shround.  note that the reason why the cover is cut off at the bottom is...

Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...

If you want the whole Orbiter mount you can find it here: =========...

Make your 3Dprinter more precise with this upgrade. ...Stabalize your leadscrew.

https://youtu.be/O0zMxpV8ilk Screen Cover Ender 3V2 Replacement item if you need a different color

REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...

Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine

Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile

i made this so i can fit noctua fan in my powersuply

will not expose the Micro SD memory and can be carried with the keys. ... upgrade to other models if desired thick walls to prevent fracture