ender 3 v2 fan upgrade 3d models
914927 3d models found related to ender 3 v2 fan upgrade.
prusaprinters
null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing
thingiverse
I remixed the LH top cover for a 92mm Noctua fan https://a.co/d/7cM5Tpj
thingiverse
Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.
cults3d
Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)
thingiverse
Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)
thingiverse
I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy
prusaprinters
This is my creation of a Y axis fan mount. ...I recently did a 24hr print and I noticed the y axis motor was kinda warm. It is designed to accept a 4010 size fan, preferably a 2 wire 24V.
thingiverse
Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.
thingiverse
(in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596...
thingiverse
... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.
thingiverse
Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...
thingiverse
... you have fan on psu this is possible you should reverse this on your Slicer. Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www .thingiverse.com/thing:4707243 Because i using a two the same fan.
thingiverse
Just a redesign to fit a 8025 fan to the psu. Needs these legs to work. ... https://www.thingiverse.com/thing:4603075
thingiverse
... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.
thingiverse
... of the 14, so instead of re-ordering I thought I would adjust this cover so it will fit. ... I did use the original cover as a stop gap by cutting away the fan shroud on the top and press fitting it through as I had already soldered in the new fan.
thingiverse
I made a little clip to hold the fan shroud in place. ...I hated turning the printer around every time I wanted to change the nozzle or get inside the fan shroud. ...I took out the screws on the back of the plate, and use this clip instead.
thingiverse
Micro Swiss hotend with two 40mm fans, never again disassemble everything - the hotend cooler is installed and the nozzle cooler screwed in. ...Now you can access everywhere easily during a fault search.
grabcad
Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.
thingiverse
I designed the original, but the long-term use was not reliable, so I designed it a little more. ...I added a curved front to accommodate the shape of the fan shroud, and a longer tab underneath
grabcad
Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.
prusaprinters
This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...
thingiverse
Changes I did: - Added enouth depth for the fan to fit inside (you will need more filament) - Cover all the holes except the fan one. Don't forget, print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking...
thingiverse
This is the Satsana fan duct where the part cooling fan is a 4020 one. To know if supports are required or not, please refer to the first link of the three above. For BLTouch, there is a gap in the mounting side that allows the stock metal bracket...
thingiverse
The original fan shroud was leaking around the bottom and cooling the heater block causing thermal runaway on the stock hotend. I modified the shroud to better cover the heater block and greatly reduced leakage. ...This shroud was added to a dual 5015...
thingiverse
Lay this flat, no support, modified satsana for direct drive clearance. ... I'll upload the direct drive file soon, needs tweaking still I cut out a lot, and tons of space by the nozzle for a LED. Its like a satsana mini but dual fan.
thingiverse
I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...
thingiverse
I've successfully manufactured three custom rail components for the Ender 3 printer and have upgraded its Y-axis with adjustable end stops as of October 27, 2018.
thingiverse
I made these for my Ender 3 Max, but they also fit on the Ender 3 Pro and the original Ender I believe. Not sure about how they fit on the V2, but someone should try. Added a few 3mm nuts and bolts and had to use a longer 10pin Display cable and a...