ender 3 v2 fan upgrade 3d models

This remix adds a clip to hang it off the fan casing. Print with no support, added a custom support for the clip. ...Cut off the support part with a knife or cutter after.

This remix adds a clip to hang it off the fan casing. Print with no support, added a custom support for the clip. ...Cut off the support part with a knife or cutter after.

It allows a 120mm fan to be installed in replacement of the small noisy stock fan. I am using a Cooler Master Pro 120. It has RGB LEDs I then tied into the string already mounted on my printer for extra cool factor! I printed at medium speed with...

I need this mod because the stock fan of 6cm was way too loud. I have a wooden box, and I need to lower the heat inside, but outside the noise is keeping me awake at night. I added a voltmeter and modified the grid to make it even more durable. The...

It enables the installation of a 120mm fan as a substitute for the small noisy stock fan. I'm utilizing a Cooler Master Pro 120, which features RGB LEDs. I integrated them into the existing string on my printer to add an extra touch of flair! ...Tips...

Summary: Does not require any supports to print Clips into place without fixings - Clips onto the ender 3v2 carriage - check your carriage has the rectangular hole below the left wheel (as you look at it) Only uses the fan screws to hold the fans in...

I made these legs for my Ender 3 v2. https://www.thingiverse.com/thing:4603075 I also made a fan board for the PSU, can be found here: https://www.thingiverse.com/thing:4601320 Buck Converter is the LM2596 Display:...

# Attribution The original designs I worked from are: [Ender 3 Cable Chain](https://www.thingiverse.com/thing:2920060) -johnniewhiskey [Ender 3 v2 attachment for bed and Z chains](https://www.thingiverse.com/thing:4565091) -wku_wake [Improved Cable...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design a...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design...

The cost for this upgrade is approximately €40.Printed parts, inserts and screws.X-AxisLeft X Shaft Holder: 2x Short M3 inserts, 2x M3x5 setscrews.Right X Shaft Holder: 2x Short M3 inserts, 2x M3x5 setscrews, 1x M4x10 socketscrews, 1x M4 T-slot...

I have remixed this awesome Ender 3 V2 mainboard fan cover https://www.thingiverse.com/thing:4643883. I remixed it adding custom supports and "mouse ears" as it was very dificult to print for my setup. So ant noobs might benefit from this. This...

Ender 3 v2 Modifications for the Hydra Includes: + E3V2 variants of rear and side brackets (threaded insert variant) + Modified Narrow default ducts with built in BLTouch 3.1 mount hugging the left side + Flat Hydra tool plate head for when using...

Extruder fan mount for Ender 3 v2 (stock extruder mount) - The problem: Hot extruder step motor + Aluminum double gear plate = soft filament. >The extruder step motor gets so hot that the heat transfers to the aluminum double gear extruder plate...

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

Simple full power supply cover replacement to install silent fan on the Meanwell PSU of the Creality Ender 3v2. This design is for 80x80x10 fan, in my case i used this one :...

Ender 3 v2 Modifications for the Hydra Includes: E3V2 variants of rear and side brackets (threaded insert variant) Modified Narrow default ducts with built in BLTouch 3.1 mount hugging the left side Flat Hydra tool plate head for when using cables...

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

This is a TinkerCAD remix for use on Ender3 V2 - to reduce noise and maximize air flow: bigger intake fan opening with chamfered edge still no fan guard (not a good choice, if you have pets or young children) more exhaust side ports - relocated...

Yet another remix of the Satsana Duct for Ender 3 v2 by x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the BTTouch bracket I used previously from Madness1561: https://www.thingiverse.com/thing:4584071 I cut out a bit of the duct...

I've been testing out various modified fan mounts for my Ender 3 using stock fans, and to be honest, many of them seem overly complicated. After printing the "MinV2 Cooler" by ThijsRio, I found this design to be refreshingly simple yet effective. To...

Then assemble everything as usual.The PSU fan will still be noticeable, but at least the hotend fan won't be annoying when idle.Printing info (already included in the 3MF if using PrusaSlicer):Material: PETG (hotend = 235*C / bed = 70*C)Layer Height:...

Found amazing Ender 3 fan cover remixed by [myeh2k](https://www.thingiverse.com/myeh2k) and decided to make it more cthulhu like. Center symbol is sigil of the gateway. Symbols on right and left are just cthulhu fhtagn written in lovecraftian font. ...

I couldn’t find a good model of a replacement for the stock fan duct on the ender 3V2 so I decided to make one myself. It took about 6 iterations to get the fit right along with the built in supports being perfect with minimal material and post work....

You can choose between these versions: cover_v2_4010 (original stock fan usage 40x40x10mm) cover_v2_4020 (if you wanna use a 40x40x20mm fan) cover_v3_XXXX (v3 versions have vertical venting holes - if you have problems with printing large bridges)...

I forgot to add a chanfer in the fan holes (the screws might not get perfectly flat with the print) PS: I used this feet -> https://www.thingiverse.com/thing:4721832 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

Remix of mplantain's original file w/ ender logo

null Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing