ender 3 v2 fan upgrade kit 3d models

Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.

(in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596...

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

... you have fan on psu this is possible you should reverse this on your Slicer. Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www .thingiverse.com/thing:4707243 Because i using a two the same fan.

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

Just a redesign to fit a 8025 fan to the psu. Needs these legs to work. ... https://www.thingiverse.com/thing:4603075

... of the 14, so instead of re-ordering I thought I would adjust this cover so it will fit. ... I did use the original cover as a stop gap by cutting away the fan shroud on the top and press fitting it through as I had already soldered in the new fan.

I made a little clip to hold the fan shroud in place. ...I hated turning the printer around every time I wanted to change the nozzle or get inside the fan shroud. ...I took out the screws on the back of the plate, and use this clip instead.

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

Micro Swiss hotend with two 40mm fans, never again disassemble everything - the hotend cooler is installed and the nozzle cooler screwed in. ...Now you can access everywhere easily during a fault search.

I designed the original, but the long-term use was not reliable, so I designed it a little more. ...I added a curved front to accommodate the shape of the fan shroud, and a longer tab underneath

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...

Changes I did: - Added enouth depth for the fan to fit inside (you will need more filament) - Cover all the holes except the fan one. Don't forget, print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking...

Lay this flat, no support, modified satsana for direct drive clearance. ... I'll upload the direct drive file soon, needs tweaking still I cut out a lot, and tons of space by the nozzle for a LED. Its like a satsana mini but dual fan.

The original fan shroud was leaking around the bottom and cooling the heater block causing thermal runaway on the stock hotend. I modified the shroud to better cover the heater block and greatly reduced leakage. ...This shroud was added to a dual 5015...

I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...

I've successfully manufactured three custom rail components for the Ender 3 printer and have upgraded its Y-axis with adjustable end stops as of October 27, 2018.

Ender 3 - Fan Guard and Silencer Kit Silencer redesigned from thing: 4276482 • Guards hot end fan • Significantly minimizes extruder fan noise • Press on friction / tab grip requiring no additional hardware • Easy removal

upgrade

Superior Filament Guide for Ender 3.

Creality Ender 3 Pro yükseltme valf kolu

:) https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 (OG) and Ender 3 Pro Ender 3 V2 Version coming Soon. Why another? Well I tried a lot of different existing designs and just wasn't happy with any...

:)https://paypal.me/cdsmakestuffDual Cooling Fan Upgrade with BLtouch MountFits Creality Ender 3 (OG) and Ender 3 ProEnder 3 V2 Version hereWhy another? Well I tried a lot of different existing designs and just wasn't happy with any of them. I wanted...

buy this and ender website

Accessorize your Ender 3 with a Japanese Torii gateway aesthetic. You will need to print 1 Middle piece either longer or shorter depending on your printer and 2 Side top and bottom pieces. For the Gakuzuka you can choose from 3 characters provided...

The only thing i spotted is that if you want a defect less print you have to print it a 101-2 % scale because when you install it on the ender 3 it cracks because it shrinks. It may be because mine was printed with ABS but i havent tried with PLA or...

This is a shelf for the ender printers. It was created with blender. To install this to the printer you will need to unscrew the x axis belt and lcd screen. You can then try and slide it in but I found I had to gently hit it with a hammer until it...

Hey Everyone, I have found a great fan upgrade for the Ender 3 v2. I don't think the creator have uploadet it here, but I think you definetly have to check this out. Great video and all the STL files here:...