ender 3 v2 fan shroud 3d models

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy

This is my creation of a Y axis fan mount. ...I recently did a 24hr print and I noticed the y axis motor was kinda warm. It is designed to accept a 4010 size fan, preferably a 2 wire 24V.

Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.

(in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596...

Just remove the top two screws from the board and reinstall them securely through the protective cover. A supplemental filter guard is designed to slide into place within the pre-drilled mounting holes. ... This printer model features an extremely...

This was modified slightly to allow for the direct drive motor to fit. ...Thanks to the original creator for an awesome design!

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

... you have fan on psu this is possible you should reverse this on your Slicer. Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www .thingiverse.com/thing:4707243 Because i using a two the same fan.

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

Just a redesign to fit a 8025 fan to the psu. Needs these legs to work. ... https://www.thingiverse.com/thing:4603075

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

Micro Swiss hotend with two 40mm fans, never again disassemble everything - the hotend cooler is installed and the nozzle cooler screwed in. ...Now you can access everywhere easily during a fault search.

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...

Changes I did: - Added enouth depth for the fan to fit inside (you will need more filament) - Cover all the holes except the fan one. Don't forget, print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking...

This is the Satsana fan duct where the part cooling fan is a 4020 one. To know if supports are required or not, please refer to the first link of the three above. For BLTouch, there is a gap in the mounting side that allows the stock metal bracket...

Lay this flat, no support, modified satsana for direct drive clearance. ... I'll upload the direct drive file soon, needs tweaking still I cut out a lot, and tons of space by the nozzle for a LED. Its like a satsana mini but dual fan.

Remix of 4969159: Adapted the file to make it fit on my Ender 3 Pro: - fixed position of M3 fixation screw - adapted one of the diameters of the two extruder fixation holders (one was too big) - fixed collision of model with M5 Nut/Screw - made the...

I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...

I'm really fond of misterpeppery's fan shroud. The nozzle's view isn't obstructed and the water test clearly shows that it blows air pretty much dead center. However, I encountered an issue - after several hours of printing, the left side starts to...

This is a fan shroud for the Ender 3 that I've modified so that it can fit alongside a BLtouch. It fits a 40x40x20 hotend fan rather than the 40x40x10 stock fan. I have it fitted with a Noctua and I kept the stock part cooling fan. Printed in PLA...

Adjusted in response to this reddit post: https://reddit.com/r/ender5/comments/uq9jjc/spider_hotend_shroud/ Remixed from: https://www.thingiverse.com/thing:5369808

Modified fan shroud for the CR10s Pro V2. ...To fit on the Micro Swiss Direct Drive kit.

Ender 3 hotend shroud for stock 40mm axial and 40mm radial fans.Required hardware:All original screws + 2x M3x25Printing orientation as in the last image.

This is a fan shroud for Ender 3 Pro that fits 40x20mm cooling fans like Sunon or Noctua, and it's fully compatible with the stock mounting screws, fan, and duct. I printed this out of PLA without any issues with warping or melting. To ensure a...