ender 3 v2 fan shroud 3d models

This remix of the eb Fan shroud and Adjustable BL-Touch mount was created to allow quick access to the hotend With this shroud mod: * Only two bolts must be removed to access the mounted hotend * The hotend and shroud are now separated, they can be...

For Ender 3 V2 A cover to put on the Power supply fan, which is very noisy during printing. ... Allow to reduce the noise during printing Just glue it using hot glue in front of the fan hole

I also used an ender 3 v2 gantry model from squirrelf to get the hole spacing right. Link to the gantry model below: https://www.thingiverse.com/thing:4779428 I used onshape to remix this model. With regards to installation you can use the...

Remix of the Red Squirrel fan shroud that adds compatibility with the MicroSwiss E3 hotend, DD mod and BLTouch. Remixed from RedSquirrelHobbies' Red Squirrel.

This fan shroud allows you to mount a Noctua 40x20 fan for the main fan (front) and a Noctua 40x10 for the parts cooling fan. Added channels to move the air down and a duct to move the air towards the parts to cool off. Has a support to mount a...

PSU Cover I designed for my 120mm quiet fan I had lying around. ...Requires custom feet to raise the printer a bit.

This is a remix of 'Ender 3 V2 & Pro Silent Motherboard' by scaryPug which is a remix of TerraVestra's design Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover houses 60x25mm fan. This cover adds 15mm, so you'll need to raise...

I liked Horvat208's (https://www.thingiverse.com/thing:4153402) 4020 hot end fan shroud, as well as mrfochs' (https://www.thingiverse.com/thing:2972610) adapter to use 40mm fans for part cooling. I could have just used them straight up, but didn't...

I appreciated [Horvat208's](https://www.thingiverse.com/thing:4153402) 4020 hot end fan shroud as well as [mrfochs'](https://www.thingiverse.com/thing:2972610) adapter to use 40mm fans for part cooling. I could have simply used them straight up,...

This is a cover for the mother board of Creality Ender 3 v2 which allows installing a 40x20 cooling fan. ... Inspired by this design: https://www.thingiverse.com/thing:4683915

This is an adapter to use two 40x40x20 Fans on the MicroSwiss Direct drive upgrade for the Ender_3_v2 2 parts to print no support needed for the duct, some needed for the mounting system. ... Lowest resolution is fine.

... ... Adapted to the Ender 3 V2 printer with Phaetus dragonfly BMS hotend and possibility of installing a BLtouch, Offset [-45, -10, 0] --------------------------------------------------------------- Voici un petit remix de du fan duct Red Squirrel.

This is my make of a shorter, slimmer fan shroud and silencer. Its quieter, shorter and prints faster. You also get the benefit of still being able to use the printable power supply tool top tray. To print just make sure its face down with the fans...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

Either use 24VDC fan or buy step-down regulator and solder it between the 12VDC fan and Ender 3 V2 motherboard. For fan I used [Noctua NF-R8 redux-1200](https://www.amazon.co.uk/gp/product/B00KF7T9MI). For step-down regulator I used [Aideepen...

This is a remix of Ender 3 V2 Satsana Fan Duct. I want to add more fan to the print head, so i designed the left side to be compatible with the same fan on the right side. ...The main purpose of this remix is to improve bridging potential.

Mainboard / motherboard cover for Ender 3 v2 with 40x40x20mm (4020) fan. You can use a 4010 as well without printer risers. Fan mounting M4, cover mounting uses stock mounting holes and hardware.Supports are optional.Pictured white PETG,...

This is a fan duct and hotend project for the Ender 3 v2 but may not be suitable for other Creality brand printers. Il s'agit d'un projet de conduit de ventilateur et de hotend pour la Ender 3 v2 mais peu convenir pour d'autre imprimante de marque...

I discovered an exceptional design in Spinnetti's Printrbot Metal Simple Fan Shroud that can be adapted perfectly on E3D hotend, and I concluded it would be better to add a cut for a snap fit without disassembling the hotend. To accomplish this, I...

After using my Ender 3 for a while, I found myself constantly searching for somewhere to store all my Micro SD cards and my single SD adapter. After looking at the Micro SD holders available, it occurred to me that the vertical fins on my fan cover...

I remix this cable chain mount from https://www.thingiverse.com/thing:4314829 so that it fits my Ender 3 V2 that is using the Satsana hotend fan shroud https://www.thingiverse.com/thing:4647053. I made one that shifts the mount over so you can...

The default petsfang needed a lil modification to work with the red lizard q1 v6, i installed this on both my ender 3 and my cr-10 this was a great hot end! like all great hot ends make sure you properly install it/assemble or you will get leaks.

Custom Mainboard housing for the Ender 3 V2 with a 92mm fan. The fan will be placed underneath and the Ender needs to be raised by whatever the amount of height the fan you are using has. The printed part works well for me, even tough a 92mm Fan is...

... MK3S+ fan duct you need. All 3 parts print without supports. The prusa duct has a built in support in the file you'll need to snap off. ABL mounts can be found here https://www.thingiverse.com/thing:3182917 Parts cooling fan is a 5015 blower.

... MK3S+ fan duct you need. All 3 parts print without supports. The prusa duct has a built in support in the file you'll need to snap off. ABL mounts can be found here https://www.thingiverse.com/thing:3182917 Parts cooling fan is a 5015 blower.

This is a basic ABL mount designed to be compatible with gibbed's eB Fan Shroud in either the 4010 or 5015 variant, or any cooling solution that leaves the x-carriage backplate completely empty. There are two main variations on this design with...

Use the same screw and install position as the original fan cover due to the fact that the V2 hotend carriage isn't threaded here (screw from the rear of the carriage as seen in the attached image).I kept the original mounting holes so this single...

I accidentaly broke two of my Ender 3 v2 neo fan blades when i was cleaning so I tried to fix it using this one: https://www.thingiverse.com/thing:4731510 and it doesnt fit so i made some adjustments to fit in the ender 3 v2 neo. To install,...

This is a double fan solution with bltouchmount for Ender 3 or V2 with the directdrivekit. Recadded fan cover and fan ducts from original parts with spot on cooling.To mount it you need some thread inserts. M2 x 4 (7 pieces) and suitable screws) for...

For installation you need 8x magnets 6mm (diameter) x 3mm (thickness) - 4 for mounting bracket, 4 for the fan duct Files for mounting bracket are also in here to download - FAN_MOD_MOUNT or FAN_MOD_MOUNT_HIGH Print Settings Printer Brand: Creality...