ender 3 v2 fan shroud upgrade 3d models

It's merely a refreshed take on a fan cover minus the usual fasteners.

Another fan cover (this one is more square and suits the profile of the machine better).

If you destroyed the whole Fan and don´t want to pay, here is a whole replacement. ...Is probably not fitting right away, because i managed to destroy, besides my whole fan, my motor too and therefore stopped designing

remix of a PrusaPrinters file: https://www.prusaprinters.org/prints/16518-fan-guard-for-prusa-i3-mk3s-snapable

I was in need of a 120mm fan mount to 3-inch exhaust out and ended up with this design when I couldn't find what I needed on TV. Plan is to drill a hole in the wall, insert 3 inches, and pump hot air from the server room up the wall to the attic...

Electronics Enthusiast's Safety Guard. ... Positioned directly beneath the printed circuit board, this protective device safeguards the fan from becoming jammed by stray plastic debris.

Just jussied a few thing up to fit my print head and wanted the extra bolt hole for a 5015 fan

Was thinking of mounting a Pi/Buck converter to the back of the Ender 3 V2, where the PSU in previous models used to be, to act as both a sleek(er) mount and a bracer to further stabilise the frame. I have already created a Pi case using this idea,...

I added some extra flair to the fan's protective covering, giving it a distinctive megalo-box aesthetic that really makes it stand out. ...It was definitely worth the effort.

Unfortunately, after printing it out, I discovered not only were the arm sides asymmetrical but also the underside of the fan cover was flat and far from aerodynamic - or symmetrical for that matter. To fix this issue, I streamlined both side arms to...

Remix of Gabriel3DCaster's CR-10 Fan Mod for Enhanced Airflow. To Optimize Print Quality, Try These Tweaks: - Tilt the duct at a different angle so air hits the nozzle indirectly. ...- Shorten it by 1mm to prevent prints from getting damaged during...

Another Ender3 Fan cover, but who doesn't like variety Best results at 0.2mm Was made using a CAD model and printed in real life without any problems. Possible to print without support but there is a bit of overhand at the top. Without support,...

Remix of Gabriel3DCaster's CR-10 Fan Mod - Airflow Optimization. Change the duct angle so the air won't directly hit the nozzle. 1mm shorter to avoid hit the print when printing. Category: 3D Printer Accessories

This is a CAD model of the Ender 3-V2. This is the original modeling for the Ender 3V2 that is used by others and published on different sites. The measurements and modeling are made from my own Ender 3V2 3D printer which I love and it works like a...

WWW.Fabricando3d.es En Inglés This is a protector for electronic fans. It doesn't require supports, so it can be printed vertically without any issues. Check the image gallery to see how to print it correctly. The inlet part is located at the back,...

feet for ender 3 35x20 Spool holder: https://www.thingiverse.com/thing:4721912

I really liked the design Ender 3 V2 Scraper & Snips Holder from ahuczekdesign but I tend to use a glass scraper more than the paint scraper so I added an extra wide slot for that to fit snugly in to place I then decided that as I us the Needle nose...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of the...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of...

I built flat covers for my ender 3 v2. The fronts fit exact size. The back one fits with the motor and if you have only one motor in the back use the front one. it will be the same size. I did mine in silver then painted it. I added a picture of what...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a 1 degree...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

Added bigger fans underneath my Ender 3v2, so it needed to be lifted. Why did I choose this design? Because I happened to have some chunks of 90x53x300 foam that I was already stacking the printer on. They provided good vibration dampening, but were...

work in progress. ...hot end housing using stock ender 3 v2 mount. hot end cover for this type of ender 3 v2 neo hot end using stock fans from ender 3 v2

Hello there, I'm Ender 3 TPU, PLA... Extruder Upgrade - a game-changing upgrade featuring a filament guide and cable holder, taking your 3D printing experience to the next level. I recently put this upgrade to the test using various materials,...

If you're familiar with Ben Levi, the renowned 3D printer constructor and developer from Israel, he's currently working on an Ender-3 Pro Upgrade kit. If you own a regular Ender-3, this corner will enable you to seamlessly integrate the upgrade on...

Remix from AustinAnywhere's EZ Vent; when I use the printer for a long time, the duct bends down due to the heat of the extruder; dragging the piece and taking it off the bed; So I added a little tab that hooks onto the extruder casing and voila,

A remix of this 100mm fan mod at https://www.thingiverse.com/ because 92mm fans are much easier to find.   Contains a replacement power supply cover and an optional 92mm fan shround.  note that the reason why the cover is cut off at the bottom is...