ender 3 v2 fan shroud upgrade 3d models
921183 3d models found related to ender 3 v2 fan shroud upgrade.
thingiverse
Features: - The shroud can be mounted directly to the extruder, allowing it to fit on most machines with enough clearance for the fan on the right side. - Close to even cooling is achieved on all sides. ...- A relatively low profile is maintained...
prusaprinters
It was designed off a Prusa MK3s Bondtech BMG fan shroud with Joel Nicklasson's fan bracket, but designed to mount to the original fan mounting location. This shroud sits close to the heat block and would be best printed with a higher temp material...
thingiverse
As I was upgrading my printer I first got a bltouch/3d touch sensor, so I first downloaded this model: https://www.thingiverse.com/thing:3003725 I later decided to replace the fans for quieter noctua 4020 on the hotend, so I printed this model...
thingiverse
Designed for use with non CR10s pro v2 hot ends (such as standard Creality end or Micro Swiss all metal) that don't extend down as low as standard hot end, . One piece. Design to print without supports. Fan side down. Two variants, required...
prusaprinters
Comes, with a slot to use a zip tie to secure cables neatly (i couldn't be bothered in the picture, but it is there to use)Uploaded version minorly different to photographed, the extra m3 nuts to lower the bltouch aren't needed in the model...
thingiverse
Reduce the high pitch noise made by my new fan. ... I added a scalled logo of the Ender dragon after the print.
prusaprinters
... Print Settings Printer Brand: Dremel Digilab Printer: 3D40 Supports: Yes Resolution: 0.1 Infill: 85 Filament: Dremel PLA Black Notes: Print with the fan mount on the build plate. ...It printed with Cura's new tree supports touching build plate only.
thingiverse
I also recessed the CR Touch screw mount so the backplate could be screwed to the gantry plate while allowing the left 4010 blower to sit flush against the fan duct backplate. Hardware Info: https://www.thingiverse.com/thing:5368944 (Optional:...
thingiverse
Thanks for the awesome fan mount from [kbowley](https://www.thingiverse.com/thing:2429054). I also loved the mounting design from [tgeehan](https://www.thingiverse.com/thing:2776707) and [keco185](https://www.thingiverse.com/thing:2448223). To solve...
thingiverse
Remix of the original fan shroud of the Micro Swiss Ender-3/CR-10 NG Extruder.Making it operational with two equal Noctua NF-A4x20 FLX for extra silent operation.
thingiverse
On paper, it should be: -30.5X, -9.5Y, ~ -0.4 Z The goal of the design was to allow for the entire hotend to be disassembled without touching the fan shroud at all. Why anyone would actually do this beats me, though it made the design process a bit...
thingiverse
Uses 2 x 5015 Blower Fans 24V. ... Update 27/03/23 - Added STL file were fan outlets are at a 45 degree angel for better paert cooling
prusaprinters
A Re-Designed kit to remove the Shroud from the Ender 3 S1/Pro Sprite Extruder This has the spacer for the breakout board and separates the CR Touch Mount to attach directly to the motor removing all the dead plastic behind the board and...
thingiverse
Just a simple cover for the fan on the psu of the ender 3. Attatches by double sided tape. ... Reduced sound by a decent amount and still leaves plenty of room for airflow.
thingiverse
This is a combo shroud that allows you to mount both a Noctua NF-A4x20 FLX 40mm fan and a BL-Touch auto-leveler to your Ender 3 Pro. You will need four M3 screws (approximately 1.5 cm in length) and nuts in order to secure the fan to the shroud. If...
thingiverse
Filename: "FanDuct_Modified_v1_Short.stl" FILES: "FanDuct_Modified_v1.stl" - Original remix (use all four fan screws or just the bottom two) "FanDuct_Modified_v1_Short.stl" - Shorter/quicker version (use only bottom two screws, do not use top two fan...
thingiverse
Remix Of VortexPC's MinionD To Fit With Spider 3.0 High Temp High Flow Hotend I Printed in PLA Fan Side On Build Plate With Organic Supports (PETG might Be Best But No Issues So Far) https://www.thingiverse.com/thing:4819097
prusaprinters
I saw this great design, but I wanted to be able to keep my stock fans because they work fine. I've attached the Fusion 360 design file, a STEP file, an STL and OBJ file. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: ...
thingiverse
The goal was use a Bondtech LGX extruder in a direct drive configuration with the Ender 7 Style dual 4010 fan shroud all mounted to a printermods MDD v1.3 plate with linear rail conversion. I am not an expert at 3D modeling so some filing and...
prusaprinters
Compatible with:Extruder :SKU M3201 - Micro Swiss NG™ Direct Drive Extruder for Creality CR-10 / Ender 3 PrintersSKU M3203 - Micro Swiss NG™ Direct Drive Extruder for Creality CR-10 / Ender 3 Printers (Linear Rail Edition)Hotend: Micro Swiss All...
thingiverse
3 fan duct lengths for Mosquito magnum hotend + adapter, Mosquito for creality hotend, and stock length hotend (Microswiss all metal, stock MK8, Creality spider etc). Must be printed with ABS, ASA, Nylon or PC! TROLLEY COLLISION ALERT! ...Use the...
thingiverse
I really love this fantastic cover and it looks incredible on the device. ...It would be even more awesome if it had the Ender emblem on it, don't you think?
thingiverse
... You may use the original mounting screws and fan. Print the fan shroud with slots facing down and use a raft (otherwise the material may not adhere to the print bed). Print without supports. ... The base plate doesn't need a raft (obviously).
thingiverse
This is an adapter to use two 40x40x20 Fans on the MicroSwiss Direct drive upgrade for the Ender_3_v2 2 parts to print no support needed for the duct, some needed for the mounting system. ... Lowest resolution is fine.
thingiverse
This is a toolless Ender 3 V2 hot end shroud/housing. It is a drop in replacement. While tools are required to uninstall the original hotend housing, installing or working on this one requires no tools. Also, replacing the two 40mm fans requires...