ender 3 v2 fan shroud upgrade 3d models

A simple hot end fan shroud that draws air from above, not the front, preventing stringy filament from getting sucked in. It just clicks right into place at the front. I removed the sticker on the front first, which might affect how well it fits.

Remix of mplantain's original file w/ ender logo

null Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

I remixed the LH top cover for a 92mm Noctua fan https://a.co/d/7cM5Tpj

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy

This is my creation of a Y axis fan mount. ...I recently did a 24hr print and I noticed the y axis motor was kinda warm. It is designed to accept a 4010 size fan, preferably a 2 wire 24V.

Adaptador melhorado para conexão do Fan 5015 mais precisa e trava deslocada 1mm para esquerda para melhorar o encaixe.

(in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596...

Just remove the top two screws from the board and reinstall them securely through the protective cover. A supplemental filter guard is designed to slide into place within the pre-drilled mounting holes. ... This printer model features an extremely...

This was modified slightly to allow for the direct drive motor to fit. ...Thanks to the original creator for an awesome design!

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

... you have fan on psu this is possible you should reverse this on your Slicer. Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www .thingiverse.com/thing:4707243 Because i using a two the same fan.

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

Just a redesign to fit a 8025 fan to the psu. Needs these legs to work. ... https://www.thingiverse.com/thing:4603075

Micro Swiss hotend with two 40mm fans, never again disassemble everything - the hotend cooler is installed and the nozzle cooler screwed in. ...Now you can access everywhere easily during a fault search.

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...

Changes I did: - Added enouth depth for the fan to fit inside (you will need more filament) - Cover all the holes except the fan one. Don't forget, print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking...

This is the Satsana fan duct where the part cooling fan is a 4020 one. To know if supports are required or not, please refer to the first link of the three above. For BLTouch, there is a gap in the mounting side that allows the stock metal bracket...

Lay this flat, no support, modified satsana for direct drive clearance. ... I'll upload the direct drive file soon, needs tweaking still I cut out a lot, and tons of space by the nozzle for a LED. Its like a satsana mini but dual fan.

Remix of 4969159: Adapted the file to make it fit on my Ender 3 Pro: - fixed position of M3 fixation screw - adapted one of the diameters of the two extruder fixation holders (one was too big) - fixed collision of model with M5 Nut/Screw - made the...

I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...

I also opened an 80mm hole for a larger fan to mount on top of the cover and added a modified fan shroud by jimb15122 (#1972504) to stop things falling into the fan. 2: I altered the PSU cover by blaahen (#4764552) by enlarging the 80mm hole a bit...