ender 3 v2 fan replacement 3d models

A "V2" as such, of this design https://www.thingiverse.com/thing:4379127, made by kylelmoy.Changes are as follows: For the motherboard and buck converter tray/plate, I reinforced and changed the mount surfaces for the base of the enclosure. Now you...

I also added spacers/standoffs that should help avoid an issue I was having, where I needed to use longer screws to mount the board, due to the soldering points on the back of my SKR Mini E3 V2. (It probably works fine with the original design, as...

This lets the fan run full speed as soon as the printer is turned on and printing rather than wait for the part cooling fan to come on later in the print or possibly never if you are printing without the part cooling fan. This is a remix from...

Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.comThis is a remix of Victor Bared's remix, in his silent fan mod upgrade videohttps://www.youtube.com/watch?v=ycvHpMbo5HwHe split the PSU cover into 3 pieces to...

Standoffs now have a ID of 4.8 mm, OD 6.3 mm and height of 3.75 mm. These values are parametric and can be adjusted. I am fairly new to modeling and have no experience sharing parametric files and very little with editing existing files. ...Let me...

Redesigned for use with Sunon fan 80x80x15mm

You'll be able to mount a 80x80x24 Fan with a buck converter in this cover.Material required:1x Buck converter --> https://www.aliexpress.com/item/32912622343.html1x 80x80 Fan --> Your choiceAssembly instructions.1) Adjust the voltage of your...

Here is a support for the ADKS duct fan to mount a BLtouch, compatible with the ENDER3 and ENDER 3 V2. It is adjustable in height. ... Thanks to the creator of ADKS - Ender 3 Fan Duct v3 for the work done.

Remixed to use one 5010 fan for mainboard cooling. ... One file (*_center) contains fan in center. ...The other one contains fan on side as the stock placement.

Bought the wrong size fan so edit the fan mount and increased the vents for better ventilation:)

Remix of an existing naked fan mount with a couple tweaks to improve fit. ...Press fit to put the fan into the fan and press fit to add the mount to the hot end, no tools required.

Have yet to print this. ...Intended for a 60mm Noctua fan I had kicking around.

CR Touch mount for this particular remix of the Satsana Fan Duct

To axial fans probably delivery barely enough part cooling to print in acceptable quality, this single part-cooling fan design does not. Also I used this design with silent noctua fans, but the part-cooling fan is surprisingly loud because of the...

Remixed this design to fit a buck converter as well as the 92mm fan. ...Useful for example for the Noctua 12V fans if your PSU only supplies 24V. ...Some PSU's might already have 12V, so check before printing.

Fan cover for thing https://www.thingiverse.com/thing:4623647 Just slide it into the 2 spare holes if you use only the 2 screws tht came with the stock fan.

This fang is designed for a 40mm hotend fan and a 60mm part cooling fan. I'm using Noctua 40x20 and 60x20 fans. For mounting the fans you need 4 x M3x30 and 4 x M4x35 countersunk screws. You may need to run an M3 and M4 tap on the screw holes for...

This product can reducing the noise of the machines 40x40 DC fan. ...Your machine will be much quieter while printing.

I took several different ideas and designed on larger fan housing for 80mm and added honeycomb cover for looks

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

Enthaltene STL-Datein: 60mm_PSU_Cover 80mm_PSU_Cover 60mm_FAN_Cover 60mm_FAN_Cover_with_GRID 80mm_FAN_Cover 80mm_FAN_Cover_with_GRID TOP_Cover_CABLE Hinweis: Ich habe die 80mm Version nicht getestet! Sollte das nicht passen würde ich mich über eine...

I used 3M heavy duty double side tape to secure the fan duct/shroud to the y-axis sensor housing (next to the stepper itself) only needs tape fan and screws to secure the fan to the duct. There are internal wind vanes to ensure proper position...

... (like shown in picture). I have fasten two parts by self-tapping screws. Just because I have no cylinder M3 screws now :) Update 08.01.2023: Add fan connector version 2. ... Have changed the mounting hole for the fan, for a more secure fit.

Pure Wings 2 fan, but should work with other 120mm fans as well. Overkill for sure, but I already had these fans on hand from an old PC build. Remixed Terminal cover as well. https://www.thingiverse.com/thing:4774312 note. Due to the extra...

... Due to the extra height feet risers are required. I used these https://www.thingiverse.com/thing:4603075. There is not enough clearance between the right rear foot and fan cover so I include modified foot to compensate for that. 

I did this in conjunction with upgrading the mainboard and psu fans to noctuas as well (https://www.thingiverse.com/make:903901) Fan: https://www.amazon.com/Noctua-NF-A4x20-PWM-Premium-Quality-Quiet/dp/B071W93333 Buck Converter:...

For my full silent build I have used: -2 x Noctua 80x80x25 fans (motherboard+PSU) -2 x Noctua 40x40x20 fans (hotend+parts cooling) -2 x adjustable converters 24 V to 12 V -PSU cover: https://www.thingiverse.com/thing:4601320 -Silent head:...

Another remix of this fantastic motherboard cover. ...This time to fit 60x25mm fan and modified/enlarged air vents and walls as well. I also had to modify the leg to make everything fit. ... (https://www.thingiverse.com/thing:4603075)

With this one, all you need to do is remove one M3 screw that holds the Fan Shroud to the Backing Plate (BL Touch plate) I recommend Printing all parts on their back and using tree supports for printing. Again, I hope you enjoy! If you decide to...

added .1mm to the blower fan opening so no sanding is required. Still a tight fit, but goes in no problem with no sanding. ... Printed mine with elegoo abs like smokey black.