ender 3 v2 fan replacement 3d models

I found those really nice designed and remixed PSU Covers for the Ender 3 V2. The original design used a 92mm Noctua A9x14 Fan which was just screwed into the cover, the remix I am referencing added a cable guide and a fan holder but uses a 80x10mm...

Summary: Does not require any supports to print Clips into place without fixings - Clips onto the ender 3v2 carriage - check your carriage has the rectangular hole below the left wheel (as you look at it) Only uses the fan screws to hold the fans in...

I made these legs for my Ender 3 v2. https://www.thingiverse.com/thing:4603075 I also made a fan board for the PSU, can be found here: https://www.thingiverse.com/thing:4601320 Buck Converter is the LM2596 Display:...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design a...

I have remixed this awesome Ender 3 V2 mainboard fan cover https://www.thingiverse.com/thing:4643883. I remixed it adding custom supports and "mouse ears" as it was very dificult to print for my setup. So ant noobs might benefit from this. This...

Ender 3 v2 Modifications for the Hydra Includes: + E3V2 variants of rear and side brackets (threaded insert variant) + Modified Narrow default ducts with built in BLTouch 3.1 mount hugging the left side + Flat Hydra tool plate head for when using...

Extruder fan mount for Ender 3 v2 (stock extruder mount) - The problem: Hot extruder step motor + Aluminum double gear plate = soft filament. >The extruder step motor gets so hot that the heat transfers to the aluminum double gear extruder plate...

The latest revision of my CAIMEO Fan Duct for the Ender 3 is now live. This upgrade takes a significant leap forward with several key improvements over its predecessor. The most notable change is the relocation of the fan to the rear, allowing for...

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

Simple full power supply cover replacement to install silent fan on the Meanwell PSU of the Creality Ender 3v2. This design is for 80x80x10 fan, in my case i used this one :...

Ender 3 v2 Modifications for the Hydra Includes: E3V2 variants of rear and side brackets (threaded insert variant) Modified Narrow default ducts with built in BLTouch 3.1 mount hugging the left side Flat Hydra tool plate head for when using cables...

You can choose between these versions: cover_v2_4010 (original stock fan usage 40x40x10mm) cover_v2_4020 (if you wanna use a 40x40x20mm fan) cover_v3_XXXX (v3 versions have vertical venting holes - if you have problems with printing large bridges)...

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

This is a TinkerCAD remix for use on Ender3 V2 - to reduce noise and maximize air flow: bigger intake fan opening with chamfered edge still no fan guard (not a good choice, if you have pets or young children) more exhaust side ports - relocated...

Yet another remix of the Satsana Duct for Ender 3 v2 by x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the BTTouch bracket I used previously from Madness1561: https://www.thingiverse.com/thing:4584071 I cut out a bit of the duct...

I've been testing out various modified fan mounts for my Ender 3 using stock fans, and to be honest, many of them seem overly complicated. After printing the "MinV2 Cooler" by ThijsRio, I found this design to be refreshingly simple yet effective. To...

Then assemble everything as usual.The PSU fan will still be noticeable, but at least the hotend fan won't be annoying when idle.Printing info (already included in the 3MF if using PrusaSlicer):Material: PETG (hotend = 235*C / bed = 70*C)Layer Height:...

Found amazing Ender 3 fan cover remixed by [myeh2k](https://www.thingiverse.com/myeh2k) and decided to make it more cthulhu like. Center symbol is sigil of the gateway. Symbols on right and left are just cthulhu fhtagn written in lovecraftian font. ...

I forgot to add a chanfer in the fan holes (the screws might not get perfectly flat with the print) PS: I used this feet -> https://www.thingiverse.com/thing:4721832 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial...

Remix of mplantain's original file w/ ender logo

null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

null Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

Print without supports. ...I snapped the metalfanguard off. My fan is more silent now ;)

I remixed the LH top cover for a 92mm Noctua fan https://a.co/d/7cM5Tpj

Adaptador para usar fan 4010 ou 4020 no resfriamento da peça.