ender 3 v2 extruder 3d models

The design is is meant to represent the Triforce from the Legend of Zelda franchise while still appearing aesthetically similar to the original knob that comes with the Ender 3 v2. I printed this in two halves and glued them together. The fit off...

... can find more technical details in the original post. Thanks ***EDIT*** (March 1st 22) I believe I have fixed the issue with the holes not lining up. This should now work for the ender 3 v2, Thanks to the person who pointed this out. ...

Un support d'extruder ajustée pour éviter que le TPU ne se coince en sortie de roue d'extrusion.

This is a new design to enable Direct Drive on Ender 3 V2 with out modifying any original parts. Take note that this only works for Metal Extruder single drive design and not yet tested on original Extruder and other types. I will be making one for...

This is a mount for the BigTreeTech (BTT) Smart Filament Sensor for a Creality Ender 3 v2 with a genuine (not a knock-off) Bondtech BMG 1.75mm extruder. This is a remix of https://www.thingiverse.com/thing:4656838 . I found that thing 4656838 did...

My Version from Creality Nebula G Sensor Mount for Sprite Extruder Pro (Remixed for Ender 3 V2)Remixed From: An adapter to mount the Creality Nebula Pad G-Force sensor to a Sprite Pro. ...Screws into the existing CR Touch...

The objective was to get the lightest and simplest set, using: - 4010 fan to the heatbreak - dual 4010 blower fans for filament cooling - BLTouch support - Extruder Stepper motor support (works with stock Ender 3[v2] or pancake) Print Tips Preferred...

The objective was to get the lightest and simplest set, using: - 4010 fan to the heatbreak - dual 4010 blower fans for filament cooling - BLTouch support - Extruder Stepper motor support (works with stock Ender 3[v2] or pancake) Print Tips...

sherpa motor mount made for my ender 3 v2 unknown if it works with anything else uses two heat set inserts for motor mounts

I accidentaly broke two of my Ender 3 v2 neo fan blades when i was cleaning so I tried to fix it using this one: https://www.thingiverse.com/thing:4731510 and it doesnt fit so i made some adjustments to fit in the ender 3 v2 neo. To install,...

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

Remixed the Ender 3 cable chain extruder mount by norp (27mm stock version) and added a shelf to mount the Big Tree Tech smart filament sensor to my Ender 3 v2. ... There are two holes in the mount so you can remove two of the factory screws from...

Through hole size increased in diameter to 4.0 mmThickness of through-hole block decreased to 5.0 mmCable distance from vertical extrusion slightly reduced to better line-up with the hot-end mounted cable clip

This mod makes the filament line straight, improving the quality of the print, aside, it saves up so much space, since the original design makes the filament go through so much loops that can bend it and make it weak, making it flow heterogeneously.

... for Spider Hotend and Stock Extruder. ... ___ I used the [More Efficient Extruder - Ender 3 and Others](https://www.thingiverse.com/thing:4586978), but it works also with the Stock Extruder. ___ Many thanks to GalvanicGlaze for the model. ...

This is a remix from https://www.thingiverse.com/thing:398515 -Edited back plate to fit ender 3 v2 with more route for cable. -Remove slot for M3 nut. -Add Bltouch mount closer to hotend for better accuracy. offset (28, 13.5, 0) -Edit prusa air...

Patreon - https://patreon.com/CosmicNimbusPrintingGumroad - https://cosmicnimbus.gumroad.com Hey fellow Ender 3 v2 Neo user ! I've been looking for a working cable chain setup for my E3v2Neo that also allows for the Direct Drive Extrusion mount on...

This small piece is a thinner replacement for the spacer between the bolt and the extruder handle. The bolt was sitting barely in the thread, causing me to damage the thread by tightening that specific bolt. As a result, I've designed a new spacer...

Extruder knob for Creality Ender-3 v2 and Ender-3 Pro, Tension Knob, BL-touch mount

Remix of 28mm model of https://www.thingiverse.com/thing:4314829 Removed the filament hole as i found it annoying and not necessary for my use case. ...Maybe someone can use this, too.

After destroying two fans so far, I decided that the Satsana fan housing needed a cover. I looked around at the free offerings and found nothing to inspire me, so here is my version. It is 3mm thick and will work with an original 40mm x 10mm fan or...

A small and clean looking extruder knob for Creality Ender 3 V2 with MicroSwiss DirectDrive extruder and Satsana duct. ...The mounting hole is bigger (103%) for easier mount to the end of the extruder.

Here's the custom extruder knob I made for my new Ender 3 V2. I found that printing the whole thing in two parts, and printing the SWTOR logo face up gives me the best results. Hope you like it! ...:)

For backplate Ender 3 V2 origin Turbo Fan 4020 and 5015

Dies ist ein Filament Guide für meinen Ender 3 V2 Drucker mit Aluminium Dual Gear Extruder. Mich hat es immer gestört, dass das Filament ständig an der Einzugsöffnung entlang schrammt. Deshalb habe ich heute den ganzen kram fast 3 Stunden vermessen...

I have remixed a set of cable chians to fit the ender V2. - Slim chain links for the x-axis - i needed 12 - 1 Extruder mount - with female attachement for the y- axis to attach - used the back mount from here:...

This mount provides a rolling Filament Guide (uses a 608 roller-skate/skateboard bearing) which aligns the filament path through the BTT smart filament sensor then directly into the BMG type extruder, when the extruded is mounted in lieu of the...

Remix of [JamieBK's direct drive mount](https://www.thingiverse.com/thing:4555065) that uses the dual gear drive extruder used with CR10

First of all, I did not create the extruder, the creator is here: https://www.youtube.com/channel/UCECzwRUtrgP9lZ2tW37NIaw For the extruder, you can acquire the files or contribute to his GitHub here: https://github.com/RoyBerntsenDesign/MJOLNIR-LWX...